Repairs; Warranty - Jilong Z-RAY I Série Manuel D'instructions

REPAIRS

Little holes or puncture can be repaired with the repair kit come along with the boat.
1. Find the leak.
2. Thoroughly clean the area surrounding the leak to remove any dirt or grime.
3. Cut a piece of repair material in round shape, which should be larger than the damaged
area.
4. Using a piece of the repair kit, trace outline of the patch lightly.
5. Apply adhesive to the underneath side of the patch and around the area to be repaired.
Coat the affected are lightly but completely with glue.
6. Put the patch on the damaged area and press down firmly.
7. Allow 12 hours for repair to dry. After patch has dried, apply glue around the edges for a
complete seal (dry 4 hours).
Limited Warranty Card
We warrant all components contained in this Laminated PVC Boat/Kayak/Stand
up Paddle Board.,etc against defects in materials and workmanship under normal
use and service, for a period of 365days from the date of purchase for the original
owner only.
If any of the components have been consumer-replaced, damaged, or misused,
the corresponding warranty on those components is invalidated. In this situation,
you will be advised of the cost of replacement parts and processing instructions.
If a verifiable manufacturing defect is found during the relevant time period, we
agree to repair or replace at its option any product under warranty provided
proper proof of purchase is presented.
This limited warranty is not valid if the product is used for commercial purposes,
or if the damage is caused by an accident, an act of God, consumer misuse,
neglect or abuse, vandalism, improper use of chemicals, exposure to extreme
weather conditions or negligence during product set up or disassembly.
We cannot be held responsible for the cost of installation, labor, or transportation
expenses incurred due to the replacement of defective parts. This limited
warranty, furthermore, does not cover any unauthorized alterations to the product.
In order to submit a claim, kindly please fill in all the parts of this form and send
it by email or fax, attaching a copy of the receipt, the description of the problem
and two photographs (as explained below, see the step #4). Jilong® is not
responsible for any expenditure on the purchase of chemical products, wasted
water, neither any consequences of water leakage. The warranty is not valid
when defects are not caused by the producer.
14 www.jilong.com ZBI-13-GB(V1)
STEP #1
DATE: / /
Surname
Address
Postal Code
Telephone
E-mail
Retailer
STEP #2
Please find out and tick the product from the following list:
Pathfinder II – 1 person Cheyenne III 200
JL007204 JL007111N
Pathfinder II – 2 person Cheyenne III 300
JL007205 JL007112N
Pathfinder – 1 person Cheyenne III 400
JL000262N JL007108N
Pathfinder – 2 person Cheyenne V 200
JL000262-1N JL007109N
FISHMAN II 400 Cheyenne V 300
JL007211N JL007101N
FISHMAN II 500
SUP Board – Native 300
JL007212N
Z-Ray IV 200 Z-Ray III 300
JL007015N JL007014N
Z-Ray IV 300 Z-Ray III 400
JL007015-1N JL007014-1N
STEP #3
Problem: Air Leakage Sewing / joint defect
Other: .................................................................................................................................
.......................................................................................................................................................
Please describe the problem in details:
..........................................................................................................................................
...........................................................................................................................................
..........................................................................................................................................
STEP #4 – Photos
a) One detailed photo of the problem
b) One general photo of the set (for example: the pool with its surrounding)
15
Name
Country
Mobile phone
Fax
Purchasing date
Z-Ray I 200
JL007012N
Z-Ray I 300
JL007012-1N
Z-Ray II 300
JL007013N
Z-Ray II 400
JL007013-1N
Z-Ray II 500
JL007013-2N
Z-Ray II 700
JL007200N
Z-Ray III 500
JL007014-2N
Z-Ray III 700
JL007201N
Puncture / Leakage Components Missing
www.jilong.com ZBI-13-GB(V1)