Eaton M-Max Série Notice D'installation page 13

M-Max Series
Adjustable Frequency Drives
FS1–FS5
Factory-Set Control Terminal Functions
Terminal Signal
1 +10V Output nominal voltage
2 AI1 Analog signal input 1
3 GND Reference potential
4 AI2 Analog input 2
5 GND Reference potential
6 24V Control voltage for DI1–DI6, output (+24V)
7 DI-C Reference potential of the digital inputs DI1–DI6
8 DI1 Digital input 1
9 DI2 Digital input 2
10 DI3 Digital input 3
13 DO– Digital output
14 DI4 Digital input 4
15 DI5 Digital input 5
16 DI6 Digital input 6
18 AO Analog output
20 DO+ Digital output
22 R13 Relay 1, normally open contact
23 R14 Relay 1, normally open contact
24 R22 Relay 2, changeover contact (N/C)
25 R21 Relay 2, changeover contact
26 R24 Relay 2, changeover contact (N/O)
A A RS485 signal A
B B RS485 signal B
1 Programmable function, see User Manual MN04020003E.
Host Computer
Factory setting
—
Frequency reference value 1
—
PID controller, actual value 1
—
—
LOGIC- (GND)
FWD start enable, forward 1
REV start enable, reverse 1
Fixed frequency B0 1
1
Active = READY
Fixed frequency B1 1
Error acknowledgment 1
PI controller deactivated 1
Output frequency 1
Supply voltage, see control signal terminal 13
Active = RUN 1
Active = RUN 1
Active = FAULT 1
Active = FAULT 1
Active = FAULT 1
BUS-communication
BUS-communication
A A
B B
2
A-B: 120 Ω A-B: 120 Ω
S1 S1
OFF OFF
Instruction Leaflet IL04020001E
Description
Maximum load 10 mA, reference potential GND
0–10V (R >200k ohms)
i
0/4–20 mA (R = 200 ohms)
B
Selectable through microswitch S2
0V
0–10V (R >200k ohms)
i
0/4–20 mA (R = 200 ohms)
B
Selectable through microswitch S3
0V
Maximum load 50 mA, reference potential GND
Selectable through microswitch LOGIC –/+
0–30V (R >12k ohms)
i
0–30V (R >12k ohms)
i
0–30V (R >12k ohms)
i
Transistor, max. 50 mA, supply voltage control signal terminal 20
0–30V (R = 12k ohms)
i
0–30V (R = 12k ohms)
i
0–30V (R = 12k ohms)
i
0–10V, max. 10 mA
Supply voltage for digital output DO max. 48 Vdc, max. 50 mA
Maximum switching load:
250 Vac/2A or 250 Vdc/0.4A
Maximum switching load:
250 Vac/2A or 250 Vdc/0.4A
Maximum switching load:
250 Vac/2A or 250 Vdc/0.4A
Maximum switching load:
250 Vac/2A or 250 Vdc/0.4A
Maximum switching load:
250 Vac/2A or 250 Vdc/0.4A
Modbus RTU
Modbus RTU
A
B
n
A-B: 120 Ω
S1
ON
EATON
Effective September 2013
www.eaton.com 13