PLYMOVENT MFE Manuel Opérateur page 17

Symptom Problem
Dust or smoke Pollution of the
coming out of facility.
the filter cover.
Machine Machine does
makes a not function
sputtering properly.
noise.
Vibrations in Machine not
the machine. steady.
8 SPARE PARTS
The following spare parts are available for the machine (refer to
exploded view Fig. I on page 50).
Article no. Description
MFE general
0000101885 Ionisation wire for FIS (10 pcs)
0050101210 Hose set (Ultra)Flex for mounting on mobile unit
0101050010 Ioniser FIS
0102080030 Aluminium pre/final filter SAF
0104060010 Activated carbon final filter SCF
0302250010 Capacitor 0,5 μF, 660V
0324150120 Control lamp 28V, yellow
0326000520 PC board HT MFE/SFE
0328100020 Safety switch, 2 poles
0328410130 Relay MC2A
0334100200 Transformer 50W/24V 115/230/400V
0340000110 Fuse 2,0 A
0609590110 Starlock 22 mm
0612010220 Adjusting ring 19x1
0708020140 Aluminium fan wheel 50Hz
0708020150 Aluminium fan wheel 60Hz
0801400010 Housing FAN 14/28/MNF/mobile units, motor side
0803010080 Insulator FCS
0803011090 Insulator FIS
0805030010 Wheel Ø 250 mm black
0805040010 Swivel castor Ø 125 mm with brake
0805040050 Swivel castor Ø 125 mm without brake
0806014020 Cover star knob M8
0840101030 Bush Ø 203 mm
9821430000 Collector FCS
9821430010 HT transformer MFE
0507250010/010513/G MFE
Possible cause Solution
Ioniser and/or Clean the filters and
collector mount them
saturated or correctly. Ref. 6.2
mounted and 6.2.4.
incorrectly.
High voltage Replace high voltage
transformer transformer.
defective.
High voltage PC Replace high voltage
board defective. PC board.
Short-circuit in Check and repair.
the ioniser and/
or collector.
Bad contact in Check and repair.
the ioniser and/
or collector.
Ioniser and/or Mount the filters
collector correctly. Ref. 6.2.4.
mounted
incorrectly.
Ioniser and/or Clean the filters. Ref.
collector 6.2.
seriously
polluted.
Not properly Let the filters dry
dried ioniser thoroughly after
and/or collector. cleaning.
Broken Replace ionisation
ionisation wires wires.
in the ioniser.
Bent lamelles in Straighten lamellas.
the collector. Ref. 6.2.3.
Metal particles in Remove metal
ioniser and/or particles and clean
collector. the filters.
Imbalance in the Clean the extraction
extraction fan. fan.
Article no. Description
9824000060 Filter cover MFD/MFE incl. outlet grid
9824000110 Mounting set safety switch MFE
9824000210 Axle
9850040090 Wheel covers yellow MFD/MFS/MFE (2 pieces)
MFE 400V/3ph/50Hz
0320000100 Motor 0,75kW, 230-400V/3ph/50Hz
0328260080 Motor protection switch MPS 1.6-2.5A
MFE 230/3ph/50Hz
0320000100 Motor 0,75kW, 230-400V/3ph/50Hz
0328260090 Motor protection switch MPS 2.5-4.0A
MFE 230/1ph/50Hz
0321012030 Motor 0,75kW, 115-230V/1ph/50-60Hz
0328260100 Motor protection switch MPS 4.0-6.3A
MFE 115/1ph/50Hz
0321012030 Motor 0,75kW, 115-230V/1ph/50-60Hz
0328260200 Motor protection switch MPS 10-16A (CSA+UL)
9 ELECTRICAL DIAGRAM
Refer to the separately supplied electrical diagram.
10 DISPOSAL
After life of the machine, dispose it of in accordance with
federal, state or local regulations.
CE DECLARATION
EC declaration of conformity for machinery
(according to Annex II A of the Machinery Directive)
We, Plymovent, Wezelkoog 11, 1822 BL Alkmaar, the
Netherlands, herewith declare, on our own responsibility, that
the machinery:
- MFE
which this declaration refers to, is/are in accordance with the
conditions of the following Directives:
- Machine Directive 2006/42 EC
- EMC 2004/108 EC
- LVD 2006/95 EC
and is/are in conformity with the following harmonized
standard(s) and/or other such normative documents +
amendments, if any:
- EN ISO 12100-1:2003 (safety of machinery)
- EN ISO 12100-2:2003 (safety of machinery)
- EN ISO 13857:2008 (safety distances)
- EN-IEC 60335-1
- EN-IEC 60335-2-65
Alkmaar, the Netherlands, May 1, 2013
Ir. F. Coehoorn
Vice President Research & Development
EN - 16