Bosch GNA 16 Professional Mode D'emploi page 9

www.motralec.com / service-commercial@motralec.com / 01.39.97.65.10
OBJ_BUCH-480-003.book Page 9 Friday, March 28, 2014 9:17 AM
Safety Warnings for Nibblers
 The power tool is not suitable for stationary operation.
For example, it may not be clamped in a vice or fastened on
a workbench.
 Wear protective gloves while working and pay particu-
lar attention to the mains cable. Sharp burrs develop at
the cut steel sheet and can cause injuries to the operator or
damage the mains cable.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and
Specifications
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for cutting sheet metal without de-
forming the material and is suitable for straight cuts, cut-outs
and narrow curves.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Die holder screw
3 Punch
4 Die holder
5 Die
6 Rubber ring for knurled screw
7 Knurled screw for die
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Bosch Power Tools
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Technical Data
Nibbler
Article number
Rated power input
Output power
Stroke rate at no load n
0
Stroke speed under load
Max. steel sheet cutting capacity*
Cutting width
Smallest curve radius
Weight according to
EPTA-Procedure 01/2003
Protection class
2
* to 400 N/mm with reference to steel sheet
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is 79 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =9 m/s , K<3 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or insertion tools
or is poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
English | 9
GNA 16
0 601 529 2..
W 350
W 160
-1
min 2200
-1
min 1600
mm 1.6
mm 5
mm 40
kg 1.7
/II
3 609 929 C96 | (28.3.14)