Publicité
11. Under no circumstances should the housing be opened.
12. Do not place your hands of legs near the rotating parts.
III. TECHNICAL DATA
Product name
Model
MULTI-GRIN135.1
Nominal power supply [V]
Frequency [Hz]
Rated power [W]
Rotating speed [r.p.m.]
Tool holderdiameter [mm]
Maximum thickness and diameter of grinding
wheel [mm]
Sound power level L
wA
Sound pressure level L
pA
Insulation Class
Protection Class
IV. SCOPE OF THE APPLICATION
The multi-function grinder is designed to be used for grinding, polishing, etching, rust removal, etc. It may be
used for woodworking, metalworking and with glass items.
The user is liable for any damage resulting from non-intended use of the device!
V. BERORE THE FIRST USE
Upon receipt of the goods, check the packaging for defects and open the packaging if there are no damages.
If the packaging is damaged, please contact your transport company and distributor within 3 days, and
document the damages as detailed as possible. Do not turn the package upside down! When transporting
the package, please ensure that it is kept horizontal and stable.
VI. DISPOSING OF THE PACKAGING
Please keep all packaging materials (cardboard, plastic tapes and Styrofoam), so that in case of a problem, the
device can be sent back to the service centre in accurate condition!
VII. INSTALLING THE APPLIANCE
POSITIONING THE DEVICE
When in use, hold the device firmly and securely in your hands. Some models have a feature for attaching
the device using a special bracket to a table top (it applies to product MULTI-GRIN135.1, MULTI-GRIN135.3
). In order to increase the work precision and comfort, a flexshaft may be used (it applies to product
MULTI-GRIN135.1, MULTI-GRIN135.3, MULTI-GRIN135.4 ). When in use, ensure unobstructed access to
the electricity plug at all times. Make sure the power source reflects the parameters on the rating plate!
8
MULTI GRINDER
MULTI-GRIN135.2
MULTI-GRIN135.3
MULTI-GRIN135.4
230~
50
135
35000
Ø3.2
1.6mm; Ø35mm
86,7dB(A), K=3dB(A)
75,7dB(A), K=3dB(A)
II
IP 20
Rev. 03.01.2019
VIII. MACHINE OPERATION – BASICS
Before using the device, make sure the required attachment or flexshaft (MULTI-GRIN135.1, MULTI
-GRIN135.3, MULTI-GRIN135.4 ) is connected firmly and securely to the clamp. Check regularly whether
the clamp is sufficiently tight. Do not turn the device on or off if the attached tool is in direct contact with
the workpiece – bring the device closer to the workpiece once it reaches its pre-set speed. To adjust the
speed, use the knob on the back of the housing. Use lower revolutions for polishing and buffing, higher for
drilling and etching. If in use for longer periods, make regular breaks to avoid overheating the device. Before
drilling on metal, mark your drill location.
1
2
3
Replacing attachments
When replacing accessories, disconnect the grinder from the power supply. In order to change tools,
press the locking button next to the clamp, unscrew the cap (by hand or using the attached wrench), then
remove the attached tool and sleeve, select the right sleeve for the new tool, insert it and screw on tightly.
When changing tools on the flexshaft (MULTI-GRIN135.1, MULTI-GRIN135.3, MULTI-GRIN135.4 ) use the
supplied wrench – it works on a similar principle to the locking button. Use the wrench to lock the clamp,
replace the tool and screw it back tightly.
If assembling fabric disks with no permanent stem attached, screw a threaded shaft onto the opening in the
middle of the disk.
If attaching disks with no permanent stem, select a shaft of an appropriate diameter, onto which the disk will
fit snugly, unscrew the locking bolt, place the disk between the gaskets and tighten the locking bolt using the
wrench.
Rev. 03.01.2019
Machine description
1.
Mounting handle
2.
Rotating adjustment knob.
3.
Lock buton
4.
Clamping bracket with nut
4 5
5.
Replaceable end
9
Publicité
