GARDEO PRO GPTRT3735BAG Traduction Des Instructions Originales page 84

properly and is in good condition.
5 Check that all handles are free from oil.
6 Check that the anti vibration system works and is
not damaged.
7 Check that the muffler is securely attached and
not damaged.
8 Check that all parts of the chain saw are tightened
and that they are damaged or missing.
9 Check that the chain catcher is in place and that it
is not damaged.
10 Check the chain tension
Kickback
- When working with the chain saw dangerous
kickbacks may occur.
- Kickback occurs when the upper part of the
end of the guide bar inadvertently touches wood
or other hard objects.
- Before the saw chain enters the cut, it can slip to
the side or jump (caution: high risk of kickback).
- This causes the saw to be thrown back toward
the user with great force and out of control. Risk of
injury!
In order to prevent kickback, follow these rules:
- Only specially-trained persons should perform
plunge cuts, i.e., piercing timber or wood with the tip
of the saw!
- Always observe the end of the guide bar. Be
careful when continuing an already started cut.
- When starting to cut the chain must be running.
- Ensure that the chain is always sharpened
correctly. Pay special attention to the height of the
depth limiter.
- Never cut several branches at the same time.
When cutting a branch ensure that no other branch
is touched.
- When crosscutting a trunk be aware of the trunks
next to it.
Working behavior/Method of
working
Always lock the chain brake before
Start the engine, otherwise the chain could be
driven to start - risk of injury!
- Only use the chain saw during good light and
visibility periods. Be aware of slippery or wet areas,
and of ice and snow (risk of slipping). The risk of
slipping is extremely high when working on recently
peeled wood (bark).
- Never work on unstable surfaces. Make sure
that there are no obstacles in the working area,
risk of stumbling. Always ensure that you have a
safe footing.
- Never saw above your shoulder height.
- Never saw while standing on a ladder .
- Never climb a tree and work without the
appropriate restraining systems for the operator
and the saw. We recommend always working
from a rising platform (cherry picker, lift).
- Do not work leaning too far over.
- Guide the chain saw in such a way that no part of
your body is within the elongated swivelling range of
the saw .
- Use the chain saw for sawing wood only.
- Avoid touching the ground with the chain saw
while it is still running.
- Never use the chain saw for lifting up or removing
pieces of wood or other objects.
- Remove foreign objects such as sand, stones
and nails found within the working area. Foreign
objects may damage the sawing device and can
cause dangerous kickback.
- When sawing precut timber use a safe
support (sawing jack). Do not
steady the workpiece with your foot, and do not
allow anyone else to hold or steady it.
- Secure round pieces against rotation.
- Before performing a crosscut firmly apply the
front of the body to the timber, only then can the
timber be cut with the chain running. For this the
chain saw is lifted at the rear handle and guided
with the tubular handle. The front of the body serves
as a centre of rotation. Continue by slightly
pressing down the tubular handle and
simultaneously pulling back the chain saw. Apply
the front of the body a little bit deeper and once
again lift the rear handle.
- When the timber must be pierced for cutting or
longitudinal cuts are to be performed it is urgently
recommended to have this carried out by specially
trained persons only (high risk of kickback).
- Do longitudinal - lengthwise - cuts at the
lowest possible angle. Be very careful when doing
this type of cut, as the front body cannot grip.
- The saw must be running whenever you remove
the chain saw from the wood.
- When performing several cuts the throttle lever
must be released in between.
- Be careful when cutting splintery wood. Cut
pieces of wood may be pulled along (risk of
injuries).
- When cutting with the upper edge of the guide
bar, the chain saw may be pushed in the direction of
the user if the chain gets clamped. For this reason
use the lower edge of the bar whenever possible.
The chain saw will then be pushed away from
you.
- If the timber is under tension, first cut the
pressure side. Then the crosscut can be performed
on the tension side. Thus clamping of the guide bar
can be avoided.
CAUTION:
People felling trees or cutting of branches must be
specially trained. High risk
of injuries!
- When cutting of branches, the chain saw should
be supported on the trunk. Do not use the end of the
bar for cutting (risk of kickback).
- Be aware of branches under tension. Do not cut
free branches from below.
- Never perform detensioning cuts while standing
on the trunk.
- Before cutting down a tree ensure that
a) only those people are within the working area
which are actually involved in cutting down the tree.
b) every worker involved can withdraw without
stumbling (the people should withdraw backwards in
a diagonal line, i. e. at a degree of 45° ).
c) the bottom part of the trunk is free from
foreign objects, underbrush and branches. Make
sure to have a safe footing (risk of stumbling).
d) the next working place is at least 2 1/2 tree
lengths away. Before cutting down the tree check
the direction of fall and make sure that there are nei-
ther people nor objects within a distance of 2 1/2
tree lengths.
- Judging the tree:
Direction of hanging - loose or dry branches - height
of the tree - natural overhang
84