Yamaha DB-A1020 Mode D'emploi page 40

SETUP menu
Video Out Select
You can select the video output resolution from HDMI,
COMPONENT, and VIDEO. For more details on output
formats, refer to "About the video output formats" (p. 39).
HDMI When set to Auto, resolution is set to the maximum
resolution according to the connected TV.
When set to Disc Native, the original resolution and
video frequency, recorded in the Blu-ray Disc or
DVD that is played back, are used. You can use a
video up-converter function of an external device.
When other than a Blu-ray Disc or DVD is played
back, the resolution and video frequency will work
as Auto.
If a Blu-ray Disc or DVD whose resolution and
video frequency are not compatible with the
connected TV, no image will be output. In this case,
stop playback, and select an option other than Disc
Native.
*
Auto , Disc Native, 480i/576i, 480p/576p,
720p, 1080i, 1080p
COMPONENT You can select only 480p/576p or 480i/576i.
480p/576p, 480i/576i*
VIDEO This works as same as 480i/576i.
Notes
– To output HD audio (Dolby TrueHD or DTS-HD
Master Audio) from HDMI terminal, set Video Out
Select to Auto or more than 720p.
– If a TV is connected with an HDMI cable, default
setting will be HDMI.
– If a TV is not connected with an HDMI cable,
default setting is VIDEO.
TV System
You can select TV System from PAL, NTSC and Multi.
Set the same TV System as your TV set. For more details
on output formats, refer to "About the video output
formats" (p. 39).
NTSC, PAL, Multi
(The default setting differs depending on your model.)
Color Space
You can select the Color Space (p. 44) output from
HDMI. This function is available when this Player is
connected with an HDMI cable.
* Sets Color Space to YCbCr 4:4:4.
YCbCr 4:4:4
YCbCr 4:2:2 Sets Color Space to YCbCr 4:2:2.
Full RGB When RGB is set and white and black on the screen
are too faint, select this item. This setting is effective
when a connected component supports RGB 0–255
range.
RGB Outputs video signal at normal signal range.
Note
– This function is only available on TVs that support
this function.
36
En
HDMI Deep Color
When your TV and/or AV receiver is compatible with
Deep Color (p. 44), set this item according to your TV/AV
receiver. This function is available when this Player is
connected with an HDMI cable.
30 bits, 36 bits, 48 bits, Off
HDMI 1080p 24Hz
This outputs the BD-Video encoded in 24Hz frame rate in
HDMI 1080p 24Hz. Smoother video playback may be
available with this function. This function is available
when your TV/AV receiver support this function, and this
Player is connected with an HDMI cable. For more details
on output formats, refer to "About the video output
formats" (p. 39).
Auto * , Off
Note
– This setting is disabled when output resolution is
other than 1080p.
Lip Sync
You can set/adjust the Lip Sync (p. 45) function.
Auto* This Player adjusts the Lip Sync function
automatically.
Manual You can adjust the Lip Sync function manually. You
can set the delay of the audio for 2D and 3D contents
independently.
2D
3D
Off This Player does not adjust the Lip Sync function.
Video Process
Video Mode
You can select Video Mode below.
Standard* The image is most natural and well-balanced. This
mode suits for normal use.
Vivid The image is more vivid and sharp.
Cinema
The image suits for watching movie in dark room.
Custom You can adjust the visual image manually. Press
5/a to select the parameter, then press 2/3 to
adjust the figure.
Brightness
Adjusts the overall brightness of the image.
Saturation
Adjusts the richness of the color in the projected
image.
Hue
Adjusts the tint of the projected image.
Contrast
Adjusts the bright areas (white levels) in the image.
Sharpness
Adjusts the sharpness of objects in the video.
CTI
Smoothes out the edges of color images. Color
images are rendered more distinct.
The default settings are 0.
*