Silverline 549095 Mode D'emploi page 5

549095
General Safety
WARNING Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
WARNING: This appliance is not intended for use by persons (including
children) with reduced, physical or mental capabilities or lack of experience or
knowledge unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety. Children must be supervised to
ensure that they do not play with the appliance.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
Automatic Battery Starter Charger 12A 6/12V
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Battery Charger Safety
WARNING: Be aware that lead-acid batteries emit flammable, explosive gases
during charging and engine cranking. Do not charge batteries close to any kind of ignition,
sparks, open flames or heat source. Do not smoke near batteries that are being charged.
If you smell gas at any time during battery charging, DO NOT disconnect clamps. Ensure
windows and doors are open to allow maximum ventilation. When gas has cleared,
disconnect charger from the mains power supply.
WARNING: When working with or near a lead-acid battery, always ensure there is
someone nearby, within vocal range, who can come to your aid if required.
• Always refer to the battery manufacturer's guidance before charging a battery
• Do not allow solvents such as paint thinner, petrol or detergents to contact the
battery case
• Unless the battery is of the 'maintenance free' type, always check that the electrolyte
level is correct before attempting to charge
• Always check the battery type (AGM, gel, etc.) and capacity (Ah) is compatible with the
battery charger
• Remove all metal jewellery before handling lead-acid batteries
• Always wear protective gloves and goggles when handling lead-acid batteries
• To prevent sparking, do not wear clothes made of synthetic fibre that may hold a
static charge
• Never use this charger to charge non-rechargeable batteries or other batteries this
charger is not designed to charge
• Use this battery charger in completely dry conditions
• Never attempt to charge a frozen battery
• Do not attempt to charge any battery that is leaking, cracked, or otherwise damaged
• If the battery charger supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard
• Ensure that there is at least 600mm of clear space around the charger to allow
adequate ventilation
• This battery charger is designed to charge one battery at a time
• Batteries should always be in a stable, upright position during charging
• Position the charger as far from the battery as charging leads will allow
• Always handle battery terminal connectors at arm's length
• Always disconnect power supply before making, or breaking, battery terminal
connections
• Do not allow any metal items to come into contact with the battery terminals
• Do not allow positive and negative lead clamps to touch
• If the battery does not appear to be charging, or displays any unusual operating
characteristics, dispose of the battery and replace
• Allow batteries to cool for 15 minutes after charging or heavy use
• Wash thoroughly with soap and water if battery acid contact skin or clothing
• If battery acid contacts eyes, wash thoroughly with clean water and seek medical help
• Batteries should always be disposed of at suitable recycling facilities. Do not dispose of
batteries with regular household waste
• Keep battery charger and batteries clean; foreign objects or dirt may cause a short
circuit. Failure to follow these instructions may cause overheating or fire
• When not in use, batteries should be stored in a dry place at room temperature (20°C).
Ensure that batteries are stored in such a way that they cannot accidentally short-circuit
in storage
• Always recycle lead acid batteries. Contact your local or national authority for the
correct recycling procedure. When returning batteries, cover the terminals with insulated
adhesive tape to prevent shorting and possible fire or explosion
• Always keep lead acid batteries out of reach of children
www.silverlinetools.com
5