Unpacking Your Water Dispenser; Preparing Your Water Dispenser For Use - Sunbeam 168 Manuel D'utilisation

UNPACKING YOUR WATER DISPENSER

ongratulations, you have acquired a high quality
C
many extra features, that you will find convenient to use. Multi-temperature capability allows you to enjoy a cool or hot
d r i n k . It will provide you with many years of trouble free use, by following the simple i n s t r u ct i o n s
contained in this manual. Please take the time to read it carefully.
1 ) Remove the water dispenser from the cardboard box
without turning it upside down, or laying it on its side.
a. Remove the strapping.
b. Open the box.
c . Remove the styrofoam packing inserts from the box .
d. Pull the water dispenser straight up from the box.
e. Remove the plastic bag.
The refrigeration compressor has very sensitive
mounts inside of its welded shell in order to
provide quiet running. Improper handling may
damage the compressor.
This water dispenser is for indoor use only.
Room temperature should not exceed 97°F / 36°C.
P R E PARING YOUR WATER DISPENSER FOR USE
1) Make sure that the water dispenser is not plugged into the electrical outlet.
2) Hold the water bottle vertically and upside down and place the water bottle into the no-spill
bottle receptacle. Apply slight pressure in order to pierce the bottle cap with the spigot. It is
not advisable to make any adjustments to the thermostat settings before the water dispenser and bottled water
are warmed up to normal room temperature. This unit accepts two, three or five gallon water bottles with with
piercable sealed caps.
3 ) Press the buttons in to let the air out, until the water starts to flow. When this happens, release the buttons.
4) Plug the water dispenser into a grounded power outlet and turn the power switch on.
5) If the water dispenser is brought in from outside in the winter time, give it a few hours to warm up to room
t e m p e rature before plugging it in. The thermostat setting may be affected by the coldness of the
water dispenser itself or the bottled water.
• The refrigeration thermostat is factory set between 7ºC and 8ºC (44.6ºF and 46.4ºF).
• The hot water thermostat is factory set between 88ºC and 89ºC (190.4ºF and 192.2ºF).
• The hot and cold indicator lights will be on while the system is working. Once the desired
temperatures have been reached, the lights will go off.
• If you choose to set the cold water thermostat to the lowest setting, it may take over one hour to cool
the water down to the coldest setting.
• Before the water dispenser leaves the factory, the thermostat is set properly. It is not advisable to
adjust the thermostat when using the water dispenser for the first time.
N OT E : When your water dispenser is in operation there is a small amount of water in the water passage
between the water tanks and the taps. This water is not controlled by the cold, hot or room
t e m p e ra t u re settings. We recommend that in order to fully enjoy the desired water setting, you
should eliminate this small amount, 200ml - 400ml (6.76 fl.oz - 13.52 fl.oz) using a small glass container.
No. 0168/0169
SUNBEAM® Water Dispenser for bottled water. This unit is packed with
2) Wipe it clean if necessary.
3) Find a location for your water dispenser that is
protected from direct sunlight and other sources
of heat. Place the water dispenser on a level
surface. Make sure that there is at least 4 inches
of space between the back of your water
dispenser and the wall. Keep a minimum
distance of 2 inches on each side of your water
dispenser free.
4) Do not plug your water dispenser into the power
outlet yet! Read the instructions first.
- 3 -
4 in.
min
PLACE
BOTTLE
VERTICALLY
STRAIGHT
DOWN