EINHELL ALUSTAR Instructions De Montage page 5

Assembly notes:
1
Assembling the floor profiles
Use profiles 1 of length 1,051.8 mm for the front
and rear walls. Use the 701.2 mm long profiles
for the lateral segments of the greenhouse.
2
Assembling the side walls
!
c
A self-tapping screw (2.9 x 14 mm) with washer
(3.2 mm) is screwed into the profile
that this screw is pointing down to the floor profile
when assembling the profile.
e
When inserting the web panels
attention to ensure that they are inserted into the
provided recess in the floor profile all the way up
to the stop. Note: The web panel must be inserted
such that the UV-coated (bonded) side points
outwards.
!
f/g
Additional Allen screws are inserted into
profiles , and
2
16
required when assembling the roof later on.
3
Preassembling the roof
Note: The item numbers (e.g.
and web panels for the rear wall have been
highlighted in gray for easier distinction in the
profile overview on page 10.
b/e
The web panel is additionally affixed on
profiles and
24 25
(4.2 x 13 mm) each.
c/e Caution, danger of mixing up: Profiles
(693 mm) for the front wall are only marginally
25
longer than profiles
are installed on the rear wall of the roof.
f-j
First connect profiles
connect two profiles
gable connector. Roof braces
attached to the ridge and web panels
from below. In the process, ensure that the
UV-coated side is facing outwards. Lastly, the web
panels are capped by profiles
side.
!
i/j
Additional Allen screws are inserted into
profiles .
21
k/l Web panels and
5
front wall and capped by profiles
bottom side. Insert two additional Allen screws into
each of the two profiles.
!
Important note:
Check all screw connections for a secure hold following assembly and retighten
if necessary.
. Ensure
12
, pay special
1
. These screws will be
17
) of the profiles
9
with three drilling screws
23
and (676 mm), which
22 24
to each other. Now
20
to each end using a ridge
11
8 are then
inserted
1
at the bottom
21
are now fastened to the
6
4 at the
m/n
Now the triangle window and both profiles
and
profiles with a connector. Note that profiles
2
and
respectively, as viewed from the outside.
!
o/p The process for assembling the rear section of the
roof is the same as for the front wall. Only one
additional web panel
Here, do not forget to insert the additional Allen
screws into profiles
Note: The vent windows on the front and rear walls
must be able to be opened approximately 80
degrees when installed correctly.
4
Assembling the roof and sway braces
Note: The roof must be installed by at least two
people.
Note that the sway braces must only be attached
at those points identified in the overview (page 14).
This will ensure optimal stability of the greenhouse.
5
Preassembling the door
b/d Ensure that web panels
such that the UV-coated side faces outwards.
f Fasten the door handle to the outside of the door
with a drilling screw (4.2 x 13 mm).
6
Assembling the door and detachable parts
and
a The door slides into the door hinge profile at
the top.
b
Now slide the latch into the lock housing.
The entire door latch and the compensation plate
are then fastened using the elongated drilling
screws (4.2 x 22 mm). For this, determine the
exact position of the door latch with the door
closed.
d Tilt the vent window forward when assembling the
ridge cover.
e/f
Suspend the window latch on the inside on the
journal at the ridge cover and make a position
marking on the web panel. Now tilt the vent
window down and mount the window latch
to the web panel using a self-tapping screw
(4.2 x 13 mm) and a washer (4.3 mm).
on the front wall are fastened to the corner
19
are assembled on the right and left,
19
is installed in the center.
3
2 and
2 and
13
13
3 .
are inserted
7
5