Switching An Element Off; Dual Element Activation; Triple Element Activation; Bridge Element Activation - FULGOR F6RT24 Série Manuel D'utilisation Et D'entretien

The control uses only the 15% of the available power,
divided in 0 to 9 steps with a better accuracy.
Keep in mind that power level 9 in this special mode
correspond exactly to level 4 in the standard range.
6HOHFW WKH ]RQH DQG WRXFK WKH >/2: 7(03@ NH\ DJDLQ
in order to disable the Low Power Scale and restore the
standard one, without switching off the zone.
Pay attention: the level remains the same but the
power increases.
Switching off a cooking zone as described below
disables the Low Power mode. When the zone will be
selected again it will start to work in the standard power
mode.
6ZLWFKLQJ DQ HOHPHQW RII
7RXFK WKH UHODWHG >2))@ NH\ UHI LQ RUGHU WR VWRS D
heating element.
You may turn off all active elements at the same time by
WRXFKLQJ WKH PDLQ >212))@ NH\
'XDO HOHPHQW DFWLYDWLRQ
6HOHFW D GRXEOH KHDWLQJ DUHD WRXFKLQJ WKH UHODWHG >21@
NH\ WKH +27 685)$&( OHG UHI EHJLQV WR ÀDVK
7RXFK WKH >'28%/(@ NH\ LQ RUGHU WR HQDEOHGLVDEOH WKH
outer ring of a double zone. This operation is possible
ZKLOH WKH +27 685)$&( OHG UHI LV ÀDVKLQJ
The dual element enabling indication (ref.5a) is on
when the element is enabled, is off when the element
is disabled.
7ULSOH HOHPHQW DFWLYDWLRQ
6HOHFW D PXOWLSOH KHDWLQJ DUHD WRXFKLQJ WKH UHODWHG >21@
NH\ WKH +27 685)$&( OHG UHI EHJLQV WR ÀDVK
7RXFK WKH >75,3/(@ NH\ LQ RUGHU WR HQDEOHGLVDEOH WKH
outer rings of a triple zone:
• If only the inner element is enabled, the intermediate
ring is enabled too.
• If the inner and the intermediate elements are
enabled, the outer ring is enabled too.
• If all the elements are enabled, the outer and the
intermediate rings are disabled.
These operations are possible until the HOT SURFACE
OHG UHI LV VWLOO ÀDVKLQJ
The intermediate element enabling indication (ref.5a) is
on when the double element is enabled, is off when the
double element is disabled.
The outer element enabling indication (ref.5b) is on
when the triple element is enabled, is off when the triple
element is disabled.
%ULGJH HOHPHQW DFWLYDWLRQ
Select one of the two single heating areas belonging
WR WKH EULGJH WRXFKLQJ WKH UHODWHG >21@ NH\ WKH +27
685)$&( OHG UHI EHJLQV WR ÀDVK
7RXFK WKH >%5,'*(@ NH\ LQ RUGHU WR HQDEOH WKH EULGJH
element and set the whole cooking area as a single
unit.
This operation is possible until the HOT SURFACE led
UHI LV VWLOO ÀDVKLQJ EHIRUH RU DIWHU VHWWLQJ WKH SRZHU
level:
• Set the power level on the selected zone then touch
WKH >%5,'*(@ NH\ ERWK WKH GLVSOD\V ZLOO VKRZ WKH
same power level and both extension lights (ref.1a,
1b) turns on.
‡ 7RXFK WKH >%5,'*(@ NH\ ERWK +27 685)$&(
OHG UHI EHJLQ WR ÀDVK DQG ERWK H[WHQVLRQ OLJKWV
(ref.6a, 6b) turns on. Set the power level that will be
immediately and simultaneously displayed on both
displays.
6b
6a
Figure. 9
2QFH WKH EULGJH FRQ¿JXUDWLRQ LV DFWLYH WKH >21@ DQG
>2))@ NH\V RI WKH WZR VLQJOH ]RQHV LQYROYHG FDQ EH
used indifferently to control the bridge area. All actions
will have the same effect on the whole cooking area.
7KH EULGJH FRQ¿JXUDWLRQ FDQQRW EH GLVDEOHG ZKLOH LV
active. It's always necessary to switch the area off: the
bridge will be disabled automatically.
+RW VXUIDFH LQGLFDWRU OLJKW
Each element has a HOT SURFACE indicator light
(ref.3) to show when the cooking area is hot.
This indication turns on when the zone is activated and
remains ON until the cooking area has cooled down to
D ³VDIH WR WRXFK´ WHPSHUDWXUH DSSUR[LPDWHO\ ƒ) 
Use & Care Manual
ENGLISH
3
3
11