English - Electrolux RENEW 800 Mode D'emploi

ENGLISH

Thank you for choosing an Electrolux product. In order to ensure the best results, always use original Electrolux
accessories and spare parts. They have been designed especially for your product. This product is designed with
the environment in mind. All plastic parts are marked for recycling purposes.
It may be possible that your steam station does not produce steam immediately after filling it with water. The reason
for this is that air trapped in the inner system can delay this function a few seconds. Please be patient and try it again
by pressing the steam button. For your convenience the steam will be produced after you release the steam button for
a few seconds and it is not necessary to press the button all the time. Find out your rhythm for the best steaming result.
COMPONENTS
A. Light indicator for heat-up/ cool-down
B. Headlight illuminating ironing area
C. Touch screen for temperature-steam programme
selection
D. Steam boost button
E. Steam hose
F. Removable water tank with integrated anti-calc
cartridge
G. Maximum water level indicator
H. Boiler unit
I. Iron rest area
J. RESILIUM™ anodized soleplate
Picture page 2-4
GETTING STARTED
1
Before first use. Remove all adhesive remains and gently rub with a dampened cloth. Position the steam station
iron horizontally on the ironing-board or on a heat resistant, secure surface at the same height as an iron-
ing-board. Unwind and straighten the power cord and the steam hose.
2
Remove the water tank (F) by gripping the slot on the underside and pulling it gently away from the boiler unit.
Detach the anti-calc cartridge (U) and then immerse it in water for more than 60 sec. Insert the anti-calc catridge
back. Fill the water tank using cold water. It is recommended to use distilled water or a mix of 50% distilled, 50%
tap water. Empty the water tank to rinse out any foreign particles which may have remained from the manufac-
turing process. We recommend to replace the anti-calc cartridge after 3 months.
3
Always refill the water tank to MAX level using cold water (F).
Caution! Never operate the appliance without any water in the tank.
4
Connect the steam station to the mains supply. Press the ON/OFF button. Select ironing programme from the
touch screen on the iron. The light indicator on the iron will pulsate when the steam station is preheating. When
turned on for the first time, temporary vapours/odours may occur.
5
As soon as the selected temperature has been reached, the light indicator is on permanently and the headlight
turns on. Now the appliance is ready to be used.
6
The steam station is equipped with ECO setting. Ironing on ECO setting in each programme selected saves up to 20%
energy consumption. ECO setting is using lower pressure, producing lower steam rate but delivering faster heat-up time.
OPERATING INSTRUCTIONS
7
Unlock the iron by switching the locking mechanism to and lift it from the iron rest area. Before starting
ironing, please test your iron on an old towel to ensure that no residues inside the iron are transferred to your
garments. If necessary, wipe the soleplate with a slightly damp cloth.
8
To activate the steam function, press and hold the steam boost button for 3-5 seconds. Hold the steam boost button to
eject a concentrated jet of steam.
rest of the steam station. It is recommended that the steam button is used for short periods.
Caution! Never release steam while the iron is standing on its rest.
9
Turn off the appliance by pressing the ON/OFF button (lighting will go off ).
10
Always cool the iron fully on the iron rest before storing away. Once the iron is cool, empty the water tank. Store the
steam station iron on the iron rest.
6
Lavignia_Renew_800_SteamStation_Elux_180918.indd 6
K. Power cord
L. Steam hose storage
M. ON/OFF button
N. ECO (ON/OFF) button
O. Tank empty indicator light
P. Carry-lock front part
Q. Locking mechanism
R. Hot soleplate indicator
S. Power cord storage
T. Boiler cap
U. Anti-calc cartridge in water tank
V. Cleaning brush
When releasing the button, use up the steam before putting it back on the iron
www.electrolux.com
2018-09-18 13:08:31