Batavia 909 Notice D'utilisation page 38

g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed
Use of the power tool for operations different from intended could
result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a. Ensure the switch is in the off position before inserting
battery pack.
Inserting the battery pack into power tools that
have the switch on invites accidents.
b. Recharge only with the charger specified by the
manufacturer
. A charger that is suitable for one type of battery
GB
pack may create a risk of fire when used with another battery pack.
c. Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create a risk
of injury and fire.
d. When battery pack is not in use,
metal objects like paper clips, coins, keys, nails, screws, or other
small metal objects that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or
a fire.
e. Under abusive conditions, liquid may be ejected from
the battery; avoid contact.
with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
6) SERVICE
a. Have your power tool serviced by qualified repair person
using only identical replacement parts.
that the safety of the power tool is maintained.
SPECIAL SAFETY INSTRUCTIONS
1. Wear ear protectors.
2. Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
and fastener may contact hidden wiring.
and fasteners contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an electric
shock.
3. Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may
contact hidden wiring.
make exposed metal parts of the power tool "live" and could give
the operator an electric shock.
4.
If possible, always use clamps or a vice to hold your work.
5.
Always switch off before you put the tool down.
6.
Ensure that the lighting is adequate.
7.
Do not put pressure on the tool, such that it slows the motor down.
Allow the bit to screw without pressure. You will get better results
and you will be taking better care of your tool.
Touch_MA_multi_1404-30.indd 38
keep it away from other
If contact accidentally occurs, flush
This will ensure
Exposure to noise can cause hearing loss.
Cutting accessory
Fasteners contacting a "live" wire may
Original Instructions
8.
Keep the area free of tripping hazards.
9.
Only use accessory bits in good condition.
.
10.
Before starting, check that there is sufficient clearance for the bit
under the work-piece.
11.
Do not touch the bit after operation. It will be very hot.
12.
Keep your hands away from under the work-piece.
13.
Never use your hands to remove dust, chips or waste close by the
bit.
14.
Rags, cloths, cord, string and the like should never be left around the
work area.
15.
Support the work properly.
16.
If you are interrupted when operating the tool, complete the process
and switch off before looking up.
17.
Periodically check that all nuts, bolts and other fixings are properly
tightened.
18.
When using the tool, use safety equipment including safety glasses
or shield, hearing protection, and protective clothing including safety
gloves. Wear a dust mask if the operation creates dust.
19.
Even when the tool is used as prescribed it is not possible to
eliminate all residual risk factors. The following hazards may arise in
connection with the tool's construction and design:
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective hearing protection is not worn.
EXTRA SAFETY REGULATIONS
CONCERNING BATTERY
• To ensure the longest battery life and best battery performance,
always charge the battery when the temperature is between
18-24°C. Do not charge the battery pack when the temperature is
below 0°C, or above 40°C. This is important. Failure to observe this
safety rule could cause serious damage to the battery pack.
• Do not incinerate the battery pack even if it is seriously damaged or
can no longer hold a charge. The battery pack can explode in a fire.
• A small leakage of liquid from the battery pack may occur under
extreme usage or temperature. This does not necessarily indicate a
failure of the battery pack. However, if the outer seal is broken and
this leakage comes into contact with your skin:
- Wash the affected area quickly with soap and water.
- Neutralise the liquid with a mild acid such as lemon juice or vinegar.
If the leakage gets in your eyes
- Flush your eyes with clean water for a minimum of 10 minutes and
seek immediate medical attention. Inform the medical staff that the
liquid is a 25-35% solution of potassium hydroxide.
• Never attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks open or cracks, immediately
discontinue its use and do not recharge it.
38
:
01-05-14 15:33