XtremeMac LUNA SST Guide De L'utilisateur page 4

4 3 5
6
7
2
1 1
1 2 3 4
4 1
3
3
2 2
6
1. LED display
2. Control knob - volume / snooze /
FM frequency
3. Play/pause controls
5
4. Source control
5. Alarm/FM radio presets
6. Detachable speaker – Alarm 1 sound
7. Snooze and Alarm 1 on/off control
8. Alarm 2 sound (attached speaker)
8
1. SST I OFF switch
2. Set clock switch
3. AUX in jack
4. 12V - 2A power jack
1. Battery compartment
2. Speaker cable jack
3. Detachable speaker alignment dots
4. Speaker brackets
1. Power button
1 2
2. Source
3. Volume controls
3
4
4. Play / pause
5
3
5. Next / previous track
6
6. Bass controls
7
7. Treble controls
8
8. Alarm / FM radio presets
9
9. Snooze / nap / sleep control
USING LUNA SST WITH SPEAKER CONNECTED
1. Untie and extend the FM antenna connected on the back of
the unit for best reception.
2. If located in the US, skip to step 5. If located outside the US,
select the appropriate wall adapter. If already attached to
the unit, skip to step 5.
3. Using a small object like a pen, press the button under the
wall adapter to release the adapter.
4. Gently slide in the appropriate wall adapter. You will hear a
click when it is properly locked into place.
5. Connect the AC adapter jack to the back of the unit labeled
12V and then connect the other end of the adapter to a
power outlet.
USING LUNA SST WITH THE SPEAKER DETACHED
PLACE SPEAKER UP TO 10 FEET/3 METERS AWAY FROM MAIN UNIT
1. Gently turn over the unit with the display and speakers
facing toward you.
2. Remove shorter speaker cable from the jacks by pushing in
the tab and pulling up. Repeat on other end and put cable in
a safe spot for reconnecting at a later date.
3. Connect longer speaker cable to the jacks on the bottom of
the unit by inserting the cable until you hear a click.
4. With the unit display facing toward you, gently slide the
right speaker toward you and pull outward.
5. Remove the two brackets on the speaker or unit by gently
sliding to unlock and pulling outward. Keep brackets in a
safe place for reconnecting.
6. Turn main unit upright and place back on a flat surface close
to a power outlet. Place the detachable wired speaker on a
flat surface up to 10 feet /3 meters away.
7. Untie and extend the FM antenna connected on the back of
the unit for best reception.
8. If located in the US, skip to step 11. If located outside the
US, select the appropriate wall adapter. If already attached
to the unit, skip to step 11.
9. Using a small object like a pen, press the button under the
wall adapter to release the adapter.
10. Gently slide in the appropriate wall adapter. You will hear a
click when it is properly locked into place.
11. Connect the AC adapter jack to the back of the unit labeled
12V and then connect the other end of the adapter to a
power outlet.
Note: For an enhanced and customized waking experience, don't forget to
download the XtremeMac alarm clock app from the iTunes App Store to your
iPhone or iPod touch device.
RECONNECTING THE SPEAKER
1. Unplug the AC adapter from the power outlet.
2. Bring detachable speaker closer to the main unit and
remove the speaker cable on the bottom of the unit.
3. With the unit display facing toward you, place the two
brackets (one on the top of the unit and one on the bottom)
into the main unit by sliding and locking into place.
4. With the speaker facing you, line up the dot on the bottom
center of the main unit with the dot on the bottom center of
the detachable speaker and gently slide back into place.
5. Connect the shorter speaker cable to the jacks on the
bottom of the unit and set the SST switch on the back of the
unit to off.
6. Connect the AC adapter jack to the back of the unit labeled
12V and then connect the other end of the adapter to a
power outlet.
SETTING THE TIME WITH YOUR IPOD OR IPHONE
Make sure the switch on the back of the unit is set to "Auto."
Dock your iPod or iPhone and the unit will automatically pull
the time from your device.
To change the time to 24 hour time, press and hold the source
button. The display will blink with 12 or 24 hour time mode. Turn
the control knob to choose 24 hour and press to confirm
the setting.
SETTING THE TIME MANUALLY
1. Make sure the switch on the back of the unit is set to "Set".
2. Press and hold the source button. The display will blink with
12 or 24 hour time mode. Turn the control knob to choose
between 12 hour and 24 hour time and press the control
to set. The display will then advance to set the time.
3. Turn the control knob to change the hour, AM or PM in 12
7