Stopping And Restarting; Loading; Drying, Cycle And Temperature Tips; Cycles - Inglis IJ70003 Guide D'utilisation Et D'entretien

2. Turn the Cycle Control knob to the recommended cycle for
the type of load being dried. Use the Energy Preferred setting
to dry most heavyweight and medium weight loads. See
"Drying, Cycle, and Temperature Tips."
3. Select a temperature setting on models with a Temp/Fabric
selector. The cycle descriptions include temperature setting
suggestions.
NOTE: The temperature selector is part of the Cycle Contol
knob on some models.
4. Select the End of Cycle Signal, if available. The signal is
helpful when drying permanent press or synthetics. Promptly
remove these items from the dryer at the end of the cycle to
prevent wrinkles.
On some models you may have:
An automatic End of Cycle Signal that will sound when
cycle is completed.
An End of Cycle Signal that can be adjusted. Turn the
selector to the desired volume.
An End of Cycle Signal that is part of the START button.
Turn the START button to ON or OFF.
5. Select the desired option. See "Additional Features."
6. Push the START button.

Stopping and Restarting

You can stop your dryer any time during a cycle.
To stop your dryer
Open the dryer door or turn the Cycle Control knob to OFF.
NOTE: The Cycle Control knob should point to an Off area when
the dryer is not in use.
To restart your dryer
1. Close the door.
2. Select a new cycle and temperature (if desired).
3. Push START.

Loading

Load clothes loosely into the dryer. Do not pack the dryer. Allow
space for clothes to tumble freely. The following chart shows
examples of balanced loads that would allow for proper tumbling.
Heavy work 3 pair of pants, 4 pair of jeans,
2 pair of overalls, 3 shirts
clothes
Delicates 3 camisoles, 1 robe, 4 slips,
6 undergarments, 2 sets of sleepwear,
1 child's outfit
Towels 10 bath towels, 10 hand towels,
14 washcloths, 1 bath mat
Mixed Load 3 double sheets, 4 pillowcases,
8 T-shirts, 6 pair of shorts, 2 blouses,
8 handkerchiefs

Drying, Cycle and Temperature Tips

Select the correct cycle and temperature for your load.
Cool Down tumbles the load without heat during the last few
minutes of all cycles to make the load easier to handle.
Drying tips
Follow care label directions when they are available.
If you use fabric softener sheets, use only those labeled
"dryer safe." Follow package instructions.
Remove the load from the dryer as soon as tumbling stops, to
reduce wrinkling. This is especially important for permanent
press, knits, and synthetic fabrics.
Cycle and temperature tips
Dry most loads using the Energy Preferred setting, if available
on your dryer.
Use a High heat setting for drying heavyweight items such as
towels and work clothes.
Use a Medium heat setting for drying medium weight items,
such as sheets, underwear, permanent press fabrics, and
some knits.
Use a Low heat setting for drying lightweight items such as
lingerie, blouses, dresses, and some knits.
Use a no-heat (air) setting for rubber, plastic, or heat-sensitive
fabrics.
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions. If you are unsure
of the temperature to select for a load, select a lower setting
rather than a higher setting.
Your model may vary from the model shown.
Cycle Control knob
Automatic Cycle(s)
Use your Automatic cycle to dry most loads. Your dryer uses
either the electronic PRECISE DRY™ system or the Automatic
Dry control. The control senses the moisture level in the load and
shuts off when the load reaches the selected dryness.
On some models
Automatic Dry (High Heat) and (Low Heat)
Select the temperature by moving the Cycle Control knob to
(High Heat) for bigger or heavier loads or (Low Heat) for
smaller or lighter loads.
Automatic Dry
Select the temperature from the temperature selector based
on the fabrics in your load.

Cycles

7