Proper Use; Technical Data; Before Starting The Equipment - Ergo tools Pattfield PE-EBH 7530 Mode D'emploi D'origine

3. Proper use

The machine is designed for digging soil (for
example garden beds). Be sure to observe the
restrictions in the safety instructions.
The operating instructions as supplied by the ma-
nufacturer must be kept and referred to in order
to ensure that the machine is properly used and
maintained. The instructions contain valuable
information on operating, maintenance and servi-
cing conditions.
For safety reasons, the machine may not be used
as a drive unit for other work tools or tool sets of
any kind.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Voltage ............................................230V ~ 50Hz
Power input ............................................... 750 W
Working width ............................................30 cm
Hoe diameter .............................................22 cm
Idle speed .............................................. 400 rpm
Number of blades .................................. 4 pieces
L noise level ..................................... 78,4 dB(A)
pA
K uncertainty: ....................................... 2,5 dB (A)
L peak noise level .............................. 93 dB(A)
WA
Vibration at the handlebars a
K uncertainty: ....................................... 1,5 dB (A)
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN ISO 3744:1995,
EN ISO 11201:1995; EN ISO 20643:2005.
Anl_PE_EBH_7530_SPK7.indb 87 Anl_PE_EBH_7530_SPK7.indb 87
GB
Keep the noise emissions and vibrations to a
minimum.
•
•
•
•
•
•
•
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
2. Damage to hearing if no suitable ear protec-
3. Health damage caused by hand-arm vib-

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Assembly (Fig. 4-11)
•
•
.............< 2.5 m/s
2
hv
•
•
•
•
- 87 -
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
mask is used.
tion is used.
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Place the motor unit and the push bars on the
ground in order (Fig. 4).
Do not forget to slide the cable strain-relief
clamp (Fig. 6/Item 5) over the bottom push
bar.
Slide the bottom push bar on to the push bar
holder and secure the two components to
each other (Fig. 5).
Now secure the top push bar to the bottom
push bar (Fig. 6).
Install the 2-hand safety switch as shown in
Fig. 7-10.
Secure the cable using the supplied cable
securing clips (Fig. 11/7)
09.10.14 08:23 09.10.14 08:23