After The Tanning/Relax Session; Transport Position; Cleaning; The Environment - Philips HB 871 Mode D'emploi

I
pressing the start button
then appear on the display.
• Type HB 875 only: the remaining time is visible on the display
but does not blink; you will have to watch the three minutes
yourself. The waiting time does not apply to the infrared lamps.
- You can shorten the set time by first pressing the
(fig. 28). The tanning lamps or infrared lamps will now be
switched off. Set the new time by means of button a. Wait
until the time indication on the display has stopped blinking and
subsequently press the start button
• Type HB 875 only: the new time is visible on the display but does
not blink. You will have to watch the three minutes yourself
(this only applies to the tanning lamps; the infrared lamps come
on right away).
Type HB 875 only:
• When you switch from a relax session to a tanning
session, bear in mind that the tanning lamps will not go
on right away. It will take a little while before they go
on.
• To be able to use the infrared lamps ('l relax' setting),
both side lamp units and the centre lamp unit should
have been put in the right position (fig. 14 and 15).
• Before you switch on the solarium, check whether the
Q Q
selector switch has been set to the desired position
('; sun' for a tanning session or 'l relax' for a relax
session).
• Make sure that the right lamps are switched on:
- For the tanning session: 4 lamps (one in every lamp
unit) that emit bluish light;
- For the relax session: 2 lamps (one in every side lamp
unit) that emit red light.

After the tanning/relax session

Let the solarium cool down for 15 minutes before you put it in
transport position and store it. During these 15 minutes, you can
roll up the cord and put it in the base of the appliance, together
with the remote control (fig. 29). Make sure you do this
carefully, as they might otherwise get stuck when you put
the appliance in transport position (fig. 30).
If your skin feels slightly taut after tanning, you can apply a
moisturising cream.

Transport position

- Turn the centre lamp unit 90° to put it in a line with the side
lamp units (fig. 31).
- Firmly hold the upper part of the stand with one hand and
loosen the height adjustment knob
clockwise (fig. 32).
- Slide in the stand (fig. 33)...
- ... and fasten the height adjustment knob by turning it clockwise
(fig. 34). Firmly fasten the knob!
- Turn the two side lamp units towards each other (fig. 35).
F
- Grab handle with both hands, put one foot against the
solarium to prevent it from sliding away and tilt the upper part
with the stand backward (fig. 36 - 38).
- NB: the automatic unlocking system will only work if
you tilt the upper part with the stand backward far
enough. However, you should be careful not to tilt it
backward too far because you might lose your balance
if you do.
- Push the upper part down and lower it slowly onto the base
(fig. 39 and 40).
- Finally, fasten the lamp units to the base by pushing both slides
in the direction of the arrow (fig. 41).
(fig. 27). The remaining time will
I
button
I
.
G
by turning it anti-

Cleaning

- Always unplug the solarium and let it cool down before you
start cleaning it.
- You can clean the outside of the solarium with a damp cloth. Be
careful not to let any water run into the appliance.
• Do not use any scourers, petrol or acetone to clean the
appliance.
- You can clean the outside of the UV filters with a soft cloth
sprinkled with some methylated spirits.

The environment

The lamps of solariums contain substances that can be harmful to
the environment. When you discard the lamps, make sure they are
not thrown away with the normal household waste but are handed
in at an official collection point.

Replacing tanning lamps, IR lamps and/or UV filters

In time (after a few years in case of normal use), the light emitted
by the tanning lamps will become less bright. When this happens,
you will notice a decrease in the tanning capacity of the appliance.
You can solve this problem by setting a slightly longer tanning time
or by having the tanning lamps replaced.
Have the infrared lamps replaced when they stop functioning.
The UV filters protect against undesired radiation. It is therefore
important to have a damaged or broken filter replaced right away.
Always have tanning lamps, infrared lamps and UV filters
replaced by an authorised Philips Service Centre. Only
they have the knowledge and skills required for this job
and the original spare parts for your solarium.
8