Getting Started - Black & Decker BCL101 Mode D'emploi

English
from materials that could contact them and cause a
short circuit.

CAUTION: GoPak battery terminal cap should be
used when battery is not connected to a power tool.
Terminal cap is provided for use whenever the battery
is out of the tool. Remove cap before placing battery
into tool.
FCC requirements for all digital devices
This device complies with Part 15 of the FCC Rules and Industry
Canada License-exempt RSS standard(s). Operation is subject to the
following two conditions:
1 . This device may not cause harmful interference, and
2 . This device must accept any interference received,
including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following meaures:
ʵ Reorient or relocate the receiving antenna.
ʵ Increase the separation between the equipment and
receiver.
ʵ Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
ʵ Consult the dealer or an experienced radio/TV
technician for help.
CAN ICES-3(B)/NMB-3(B)

Getting Started

• The micro USB port
in 1 battery is only to be used for charging the GoPak.
• The USB A port 14 on the BLACK+DECKER GoPak 2 in 1
battery is only to be used for powering USB devices
(Phone/Tablet/MP3/Wearable/Game Controller/etc.).
Fig. B
14
4
7 on the BLACK+DECKER GoPak 2
Charging the BLACK+DECKER GoPak 2 in 1
Battery (Fig. C, D)

WARNING: Never attempt to charge the
BLACK+DECKER GoPak 2 in 1 battery using the tool
terminals on the GoPak.

WARNING: You should only charge the
BLACK+DECKER GoPak 2 in 1 battery using UL or
CSA approved USB ports rated for charging high
performance devices. The GoPak can pull more
current than acceptable with older USB ports. An
error message may display on your computer if the
computer is used to charge the GoPak.
1. Plug the micro USB cable
(not included).
2. Plug the micro USB plug of your charger cord into the
GoPak micro USB port
3. As the GoPak charges, the state of charge LEDs will
illuminate. The illuminated LED(s) indicate the state
of charge of the pack. The blinking LED indicates the
next level of charge in progress. The state of charge
button 9 is disabled during charging only.
4. The completion of charge is indicated by all four LEDs
turning off. Pressing the state of charge indicator
button will illuminate all four LEDs. The battery is
9
fully charged and may be used at this time or left on
the charger.
5. Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished. For
longest battery life, do not discharge batteries fully. It
is recommended that the batteries be recharged after
each use.
Fig. C
8
State of Charge Indicator (Fig. D)
The BLACK+DECKER GoPak 2 in 1 battery is equipped with a
state of charge button
The state of charge is an indication of approximate levels
of charge remaining in the battery according to the
following indicators:
7
8 into a USB power supply
.
7
9 with a four LED display.
7