Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1
PRESENTATION AND GENERAL POINTS
1.1 GENERAL POINTS
The DELTA ADVANCE cutting machine has been designed taking into account the
safety regulations in force in the EEC.
The safety of the personnel involved in the handling of this type of machine is
only achieved with a well-designed personal safety programme, such as the
implementation of a maintenance programme and follow-up to the recommended
advice, as well as compliance with safety regulations contained in this manual.
Although the installation of the machine presents no difficulty, it is preferable that you
do not attempt to install, adjust or handle it without reading this manual first.
The machine leaves our factory ready for use and only needs calibration operations
for the tools that are going to be used.
1.2 TRANSPORTATION AND PACKAGING
The DELTA ADVANCE machine is presented in a sturdy cardboard box protected
with packaging foam, of the following dimensions:
Width = 570 mm; Depth = 570 mm; Height = 380 mm;
Weight (including packaging) = 28 Kg.
When unpacking the machine, carefully inspect it for any damage during transport.
If you find any anomaly, immediately notify the carrier and do nothing with the
machine until the carrier's agent has carried out the corresponding inspection.
To move the machine from one place to another, we recommend that you only lift the
machine by its base and not by other parts.
1.3 IDENTIFYING LABEL
The DELTA ADVANCE cutting machine comes with an identifying label, with
specification of the serial number or machine registration, name and address of the
manufacturer, CE mark and year of manufacture.
2
MACHINE FEATURES
The DELTA ADVANCE is a modern cutting machine for mortise-type keys and frontal
keys.
2.1 ACCESSORIES
The machine is supplied with a series of accessories for its use and maintenance:
- 2 Counterpoints for female keys with narrow holes
- 2 Counterpoints for female keys with wide holes
- 2 Counterpoints for special male keys
- 2 Rods to make the adjustment (Ø5x70)
- 1 Rod for the change of cutter or brush ( 7x70)
- 1 Fixed key of 18
- 1 Set of Allen keys (2, 2.5, 3, 4, 5, 6)
2.2 ELECTRICAL CIRCUIT
The main components of the electrical and electronic circuit are the following:
1. Plug
2. Start switch (RED light)
3. Push button for brush (BLACK)
4. Motor
5. Transformer
6. LED lighting diodes
7. Connection plate
14
DELTA ADVANCE
instruction manual
2.3 TECHNICAL DATA
Motor: Single phase 220V; 50Hz; 0,25Kw; 1,500 rpm (Optional: 110V; 60Hz; 0,25Kw;
1,500 rpm)
Cutter: FP19 HSS (Ø80x1.4x16)
Cutter speed: 750 rpm
Transmission: Ribbed belt.
Clamps: Self-centring
Movements: Guides with roller cages
Useful courses: X = 62 mm; Y = 47 mm
Lights: Led
Dimensions: Width = 370 mm; Depth = 460 mm; Height: 260 mm
Weight: 26 Kg
2.4 NOMENCLATURE OF THE KEY
1
1. Head
2. Stem
3. Bit
4. Teeth
2.5 MAIN ELEMENTS OF THE MACHINE
11.- Push button of the brush
1.- Cutter
12.- Adjustment control in depth of the probe
2.- Brush
13.- Carriage fixing handle
3.- Clamp
14.- Carriage locking handle in the X direction
4.- Clamp handle
15.- Handle for the probe's spring
5.- Carriage forward control
16.- Grip lock handle of the clamp
6.- Round point control
17.- Tray for accessories
7.- Probe support
18.- Hole for locking the head
8.- Copier index
19.- Chip tray
9.- Lighting
20.- General power socket
10.-Start-up switch
12
7
20
11
10
15
19
8
3
4
2.6 COMPONENTS AND FUNCTIONAL PARTS
2.6.1 CLAMP
The clamp is a fundamental part of the DELTA ADVANCE machine. It has been
studied to be able to cut as many keys as possible, using counterpoints for the
cutting of some of them.
2.6.2 ROTATION LOCK OF THE RIGHT-HAND SIDE CLAMP
The clamp on the right side of the BIT carriage has the handle "16", which allows the
locking and unlocking of the rotation.
Locking the rotation of this clamp is useful for:
•
Copying frontal keys.
•
Facilitating the fastening of the keys in the clamp.
•
Facilitating the realization of the "bit stop against the cutter" (in the case of
short keys).
2.6.3 COUNTERPOINTS (USE MODE)
The DELTA ADVANCE machine has three pairs of counterpoints, to facilitate the
attachment of different types of keys:
4
3
2
17
1
9
18
2
16
6
5
13
14
Publicité
Table des Matières
