Metabo WEVF 10-125 Quick Inox Notice Originale page 16

en ENGLISH
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 Clip to tighten/release the (tool-free) clamping
nut manually *
2 Clamping nut (tool-free) *
3 Support flange
4 Spindle
5 Spindle locking button
6 Safety cover
7 Side handle/Additional handle with vibration
damping *
8 Sliding on/off switch *
9 Handle
10 Electronic signal indicator
11 Speed adjustment wheel *
12 Switch-on lock*
13 Trigger switch *
14 Lever for safety guard attachment
* depending on equipment/not in scope of delivery
6. Commissioning
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
6.1 Attaching the additional handle
Always work with the additional handle (7)
attached! Attach the additional handle on the
left or right of the machine and secure.
6.2 Attach the safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter 11. Accessories!
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cutting discs.
See illustration C on page 2.
- Place the safety guard (6) in the position
indicated.
- Push the lever (14) and turn the safety guard until
the closed section is facing the operator.
- Release lever and rotate guard
until the lever latches.
- Make sure that the guard is placed securely: The
lever must engage and you should not be able to
turn the safety guard.
16
7. Attaching the grinding wheel
Prior to any conversion work: Pull the mains
plug from the socket. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the cut-off
grinding guard before performing cut-off
grinding work (see Chapter 11. Accessories).
7.1 Locking the spindle
Press in the spindle locking button (5) only
when the spindle is stationary.
- Press in the spindle locking button (5) and
turn the spindle (4) by hand until the spindle
locking button engages.
7.2 Placing the grinding wheel in position
See illustration B on page 2.
- Fit the support flange (3) on the spindle. The
flange should not turn on the spindle when
properly attached.
- Place the grinding wheel on the support flange (3).
The grinding wheel must lay flat on the supporting
flange.
7.3 Securing/releasing the (tool-free)
clamping nut
Only tighten the (tool-free) clamping nut (2) by
hand!
For the machine to operate, the clip (1) must
always lie flat on the clamping nut (2).
To secure the (tool-free) clamping nut (2):
Use only accessories which fulfil the
specifications. See Chapter 14. Technical
Data).
- Lock the spindle (see chapter 7.1).
- Flip up the clip (1) on the clamping nut.
- Fit the clamping nut (2) on the spindle (4). See
illustration A on page 2.
- Tighten the clamping nut on the clip (1) manually
in a clockwise direction.
- Flip down the clip (1) again .
Release the (tool-free) clamping nut (2):
- Lock the spindle (see chapter 7.1).
- Flip up the clip (1) on the clamping nut.
- Unscrew the clamping nut (2), turning it
anticlockwise manually .
Note: If the clamping nut (2) is very tightly secured,
you can also use a 2-hole spanner to unscrew it.
Use only accessories that
are covered by at least 3.4
mm by the safety guard.
(Disassemble in reverse
order.)