Metos TQ-10 Mode D'emploi page 12

TQ-10 & TQ-15 MODELS
1. Plug toaster into a properly grounded electrical outlet
of the correct voltage, size and plug configuration. See
SPECIFICATIONS for details.
2. To toast the top and bottom sides
of the bread, place the TOP HEAT and BOTTOM HEAT
switches in the ON position.
To toast on the top side only, place the TOP HEAT switch
in the ON position and the BOTTOM HEAT switch
in the OFF position.
To toast on the bottom side only, place the TOP HEAT
switch in the OFF position and the BOTTOM HEAT switch
in the ON position.
See Figure 12 .
3. Turn the COLOR CONTROL to the lightest position while
the unit heats up.
NOTE: Allow approximately 15 to 20 minutes
for a warm-up period.
4. After warm-up period, set the COLOR CONTROL
to the medium position and toast two slices of bread product
then re-adjust the COLOR CONTROL to the desired setting.
NOTE: To toast moist products such as English Muffins, rye bread
or whole wheat, slow the conveyor by turning the COLOR
CONTROL knob to a darker setting (clockwise).
TQ-400, -405, -800, -805, -800H & -1200 MODELS
1. Plug toaster into a properly grounded electrical outlet
of the correct voltage, size and plug configuration. See
SPECIFICATIONS for details.
2. Place the On/Off switch in the ON position.
See 13 .
3. Turn the TOP HEAT Control and BOTTOM HEAT Control
clockwise to the highest setting.
4. Turn the COLOR CONTROL to the lightest position while the
toaster heats up.
NOTE: Allow approximately 15 to 20 minutes
for a warm-up period.
5. After warm-up period, toast two slices of bread product. Adjust
the COLOR CONTROL if needed.
NOTE: If toasted bread is too dark with the Color Control
set on the lightest setting, adjust the bottom and top heat controls
as needed. (Allow 15 to 20 minutes for toaster to re-adjust to new
setting before resuming operation.)
NOTE: To toast moist products such as English Muffins, rye bread
or whole wheat, slow the conveyor by turning the Color Control
knob to a darker setting (clockwise).
NOTE: When toasting on a single-sided product such
as a bun or bagel place the product with the cut side facing
up. Adjust the Bottom Heat Control to a light setting, toast two
slices of bread product and adjust the Top and Bottom Heat Control
as needed.
TQ-400BA, -800BA & -800HBA MODELS
NOTE: TQ-400BA, -800BA and -800HBA toasters are designed
specifically for toasting one side of a bread product, such as a bun
or bagel. These models toast with the cut side facing up.
1. Plug toaster into a properly grounded electrical outlet
of the correct voltage, size and plug configuration. See
SPECIFICATIONS for details.
2. Place the On/Off switch in the ON position.
See 13 .
3. Turn the TOP HEAT Control clockwise to the highest setting.
Turn the BOTTOM HEAT Control counter-clockwise
to the lowest setting.
4. Turn the COLOR CONTROL to the lightest position while the
toaster heats up.
NOTE: Allow approximately 15 to 20 minutes
for a warm-up period.
5. After warm up period, toast two slices of bread product. Adjust
the COLOR CONTROL if needed.
NOTE: If cut-side of bread product is too dark with the Color
Control set on the lightest setting, adjust the Top Heat Control
as needed. (Allow 15-20 minutes for toaster to re-adjust to new
setting before resuming operation.)
POWER SAVE MODE WITH INDICATOR
LIGHT
All TQ-400, -800 and -1200 series toasters have a built-in Power
Save Mode with Indicator light feature. This feature allows the
toaster to go into stand-by and reduces power to the heating
elements by 50%. During the Power Save Mode the indicator light
on the control panel will flash.
To activate press the POWER SAVE Mode button until
the indicator light flashes. See 13 .
NOTE: To place toaster back into full operation push the Power
Save button or turn any knob until the indicator light stops flashing
and stays on. Allow a minimum of 2-3 minutes before toasting. Unit
is back up to full power within 10 minutes.
COLORGUARD SYSTEM
All TQ-400, -800 and -1200 series toasters use a patented
ColorGuard Sensing System that monitors and automatically adjust
conveyor speed during high usage periods to assure toast
color uniformity.
NOTE: The ColorGuard Sensing System is inoperable for
approximately ten minutes after any heat adjustments are made.
10
OPERATION
Form No. TQ2CEM-0903