Technical Data; Warranty Certificate; Declaration Of Conformity - EMAK BTC 36 V Manuel D'utilisation Et D'entretien

WARNING! Always disconnect the battery charger from
the mains power supply when you finish recharging
the battery
ATTENTION! If the rechargeable battery pack fail to charge,
check whether there is voltage at the socket outlet. If you are
unable to charge the battery, contact an authorized service centre.
Timely recharging of the battery will help it to serve you well for a
long time. You must recharge the battery pack when you notice that
the power of the equipment drops.
STORAGE
Store the battery charger out of reach of children in a dry place away
from direct sunlight and at above-zero temperature. Store the
charger only in dry places with an ambient temperature of 10-40°C.
Keep the original packing for storage and transport of the battery
charger.

TECHNICAL DATA

Power
Mains power supply
Frequency

WARRANTY CERTIFICATE

This machine has been designed and manufactured using the most
modern techniques. The manufacturer guarantees its products for 24
months from the date of purchase, for private and hobby use. The
warranty is limited to 12 months in case of professional use.
PROBLEM
The battery charger does not charge the
battery (green indicator light on)
The battery charger does not charge the
battery (no red led on)
The battery charger does not charge the
battery (no red led on)
The undersigned,
declares under its own responsibility that the machine:
1. Type:
2. Trademark: / Type:
3. serial identifi cation
complies with the requirements
established by directive
conforms with the provisions of the
following harmonised standards:
Made at:
Date:
Technical documentation available by:
W 100
V 100-240
Hz 50/60
TROUBLESHOOTING
POSSIBLE CAUSE
Dirty contacts
No power supply to battery charger
Defective battery charger or cable

DECLARATION OF CONFORMITY

EMAK spa via Fermi, 4 - 42011 Bagnolo in Piano (RE) ITALY
BATTERY CHARGER
EMAK BTC 36 V
642 XXX 0001 - 642 XXX 9999
2006/95/EC - 2004/108/EC - 2011/65/EC - 2006/66/EC
EN 60335-1 - EN 60335-2-29 - EN 55014-1+A1+A2 - EN 55014-2 - EN 61000-3-2 - EN 61000-3-3
Bagnolo in piano (RE) Italy - via Fermi, 4
01/03/2014
the administrative authorities. - Technical Department
Limited warranty
1) The warranty period starts on the date of purchase. The
manufacturer, acting through the sales and technical assistance
network, shall replace free of charge any parts proven defective in
material, machining or manufacturing. The warranty does not
affect the purchaser's rights as established under legislation
governing the consequences of defects in the machine.
2) Technical personnel will undertake the necessary repairs in the
minimum time possible, compatible with organisational needs.
3) To make a claim under warranty, proof of purchase in the
form of an invoice or till receipt must be shown to the
authorized company representative.
4) The warranty shall be null and void if:
• the machine has evidently not been serviced correctly
• the machine has been used for improper purposes or has been
modified in any way,
• unsuitable lubricants and fuels have been used
• non-original spare parts and accessories have been fitted
• work has been done on the machine by unauthorised personnel
5) The warranty does not cover consumables or parts subject to
normal wear.
6) The warranty does not cover work to update or improve the
machine.
7) The warranty does not cover any preparation or servicing work
required during the warranty period.
8) Damage incurred during transport must be immediately brought
to the attention of the carrier: failure to do so shall render the
warranty null and void.
9) The warranty does not cover injury or damage caused directly or
indirectly to persons or things by defects in the machine or by
periods of extended disuse of the machine resulting from the said
defects.
Clean contacts
Check the plug is inserted and that the
socket receives power
Replace the battery charger
SOLUTION
s.p.a.
Fausto Bellamico - President
7