Wire Sizing & Gland Sizing; Evfx Pattern Size Chart - Kasco 2400EVX Guide D'utilisation

Wire Sizing & Gland Sizing
The chart below shows the proper Gland to be used
with different cord sizes. The measurements are based
on the Outside Diameter (O.D.) of the cord. Smooth,
round cords should be used.
Kasco Quick Disconnect 50 Hz Size Chart:
Gland
Grey
White
Black
Yellow
Kasco 50 Hz Equipment Wire Size Chart
Model
10m
1.5mm 2 1.5mm 2 2.5mm 2
2400EVX
1.5mm 2 1.5mm 2 2.5mm 2
2400EJ
1.5mm 2 1.5mm 2 2.5mm 2
3400EVX
1.5mm 2 1.5mm 2 2.5mm 2
3400EJ
1.5mm 2 1.5mm 2 2.5mm 2
4400EVX
1.5mm 2 1.5mm 2 2.5mm 2
4400EJ
2400EVX, 2400EJ, 3400EVX, 3400EJ,
4400EVX Parts
1. EV or EJ Aerating Fountain (Unit with cord or
stub cord) (1)
2. Float(with two 50' mooring ropes attached) (1)
3. 1/4-20 long Phillips Pan Head Screw (4)
4. 1/4" split washers (7)
5. 1/4" (3/4" outer diameter) Flat Washer (10)
6. 1/4"-20 x 1-3/4" Hex Head Bolt (3)
7. Bottom Screen Section (3)
8. 1/4"-20 Nut (2)
9. #8 nut (6)
10. #8 flat washer (12)
11. #8 lock washer (6)
12. #8 x 1/2" Screw (6)
O.D. of Cord
7-9mm
9-11mm
11-13mm
13-15mm
Cord Length
30m 60m 90m
2.5mm 2
2.5mm 2
2.5mm 2
2.5mm 2
4mm 2
4mm 2
6
5
9 10
Also included: (not pictured)
DO NOT SCALE DRAWING
C.A.D. GENERATED DRAWING
• Interchangeable nozzles for 2400EJF, 3400EJF
THIS DOCUMENT HAS BEEN ISSUED
DIMENSIONS IN [ ] ARE MILLIMETERS.
FOR ENGINEERING INFORMATIONAL
PURPOSES ONLY. ANY REVISIONS
only (See 2400EJ 3400EJ Nozzle Options section)
.X
TO THE CONTENT OF THIS DOCUMENT
MUST BE INCORPORATED INTO THE
.XXX
ORIGINAL CAD FILE.
• Nylon Cable Tie
THIS DRAWING CONTAINS PROPRIETARY
THIRD ANGLE PROJECTION INFORMATION AND SHALL NOT BE USED,
REPRODUCED OR DISTRIBUTED WITHOUT
THE PRIOR WRITTEN CONSENT OF
KASCO MARINE, INCORPORATED
TOOLS & SUPPLIES NEEDED
A. Anchors or stakes for installing unit (2)
B. # 2 Phillips head screw driver
C. 208-240V Electrical Supply near pond on a post
D. 7/16" (12mm) Socket and Ratchet
E. 7/16" (12mm) Wrench

EVFX Pattern Size Chart

All produce a V-shaped display.
Model
2400EVX
3400EVX
4400EVX
11 12
MATERIAL:
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES. X
X
TOLERANCES ON:
FINISH:
.02 [.508] .XX .010 [.254]
X
.005 [.127] ANGULAR 0.5
X
TITLE:
X
Height
1.15 m
1.7 m
1.7 m
X
DWG. NO.
3
4
5
2
1
7
5
4
8
800 D
PRESCOT
SCALE: 1:20
XXXX
Width
4.3 m
6.1 m
6.7 m
5