Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Power
V 6 2
Protect
POWER AMPLIFIER
Power
V 6 2
IN MONO MODE ALL INPUT JACKS ARE IN PARALLEL
ALL INPUTS ARE BALANCED
B
A
AMPLIFIER INPUTS
Channel
Introduction
Your new VTC Pro Audio V62 power amplifier is designed and built to provide years of trouble free performance.
The V62 weighs a comfortable but solid 66.1 pounds, fits into three rack spaces, and reproduces music with
over 7000 Watts of headroom. It will drive reactive phase shifted loads with no difficulty – even though it is fully
protected from accidental short circuits. Our design goal was to create an amplifier which would do exactly what an
amplifier should do: reproduce music with great power, complete reliability, and uncompromising signal fidelity. We
think you will agree that the VTC Pro Audio V62 does exactly that.
Inputs
1. Balanced Inputs
Either XLR or two-circuit 'Ring, Tip, Sleeve' Stereo 1/4-inch PHONE cords may be used. Each channel's XLR input
is internally paralleled with its phone input (The TIP of the channel 'A' PHONE input is connected to pin 2 of its XLR
input, the RING is connected to pin 3, and the Sleeve is connected to PIN 1). PIN 2 is in phase, PIN 3 is 180 degrees
out of phase, and PIN 1 is ground.
2. Unbalanced Inputs
Ordinary single circuit Standard 1/4-inch PHONE plugs may be used to connect unbalanced signals.
Push to
Reset
WARNING: SHOCK HAZARD • DO NOT OPEN
AVIS: RISQUE DE CHOC • NE PAS OUVRIR
WARNING: RISK OF HAZARDOUS ENERGY! SEE OPERATING MANUAL.
AVERTISSEMENT: ÉNERGIE ÉLECTRIQUE DANGEREUSE! VOIR LE CAHIER D'INSTRUCTION.
GROUND
SUBSONIC
LIMITER
STEREO
CONNECTED
FILTER
ENABLE
MONO
BRIDGE
20 Hz
MODE
SUBSONIC
GROUND
LIMITER
FILTER
Channel
LIFTED
DEFEAT
40 Hz
NOTE: Such plugs effectively connect the ring terminal to sleeve ground, so they
work correctly. However, if you use a Stereo 1/4-inch PHONE plug on an unbalanced
line, you MUST short the Ring terminal to the sleeve terminal, otherwise the
sensitivity will be 6 dB lower than is specified! (The same applies to the XLR input:
To connect an unbalanced source via the XLR input, you must connect the signal to
Pin 2 and ground both Pin 1 and Pin 3).
Channel A
-15
-18
-21
Clip
Signal
-30
-0 0
-0 0
0
0
dB
A-Z1261 / 1v0
120VAC
230V
MODEL TYPE:
60Hz 15A
50Hz 8A
YS6020
BRIDGED MODE 4-OHMS MINIMUM
S P E A KO N ™ P I N C O N F I G U R AT I O N
TWO CABLES
SINGLE CABLE OUTPUT
BRIDGE MODE CABLE
B
(
1+
)
(
1+
)
A / B
(
1+
)
(
2+
)
A / B
(
)
(
A
B
1+
1–
1–
1–
2–
Ch
2000 WATTS
S P E A K E R O U T P U T S
2-OHMS MIN
Channel B
-15
-18
-12
-12
-9
-9
-21
Clip
-6
-6
-3
Signal
-3
-30
-0 0
-0 0
0
0
dB
MADE IN CANADA
A / B
)
A
2+
BRIDGED
Ch
2000 WATTS
2-OHMS MIN
1
Publicité
Table des Matières
