Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Power
V 64
Protect
POWER AMPLIFIER
Power
V 6 4
IN MONO MODE ALL INPUT JACKS ARE IN PARALLEL
ALL INPUTS ARE BALANCED
B
A
AMPLIFIER INPUTS
Channel
Introduction
Your new VTC Pro Audio V64 power amplifier is designed and built to provide years of trouble free performance.
The V64 weighs a comfortable but solid 66.1 pounds, fits into three rack spaces, and reproduces music with over
7000 Watts of headroom. It will drive reactive phase shifted loads with no difficulty - even though it is fully protected
from accidental short circuits. Our design goal was to create an amplifier which would do exactly what an amplifier
should do: reproduce music with great power, complete reliability, and uncompromising signal fidelity. We think you
will agree that the VTC Pro Audio V64 does exactly that.
Inputs
1. Balanced Inputs
Either XLR or two–circuit 'Ring, Tip, Sleeve' Stereo 1/4-inch PHONE cords may be used. Each channel's XLR input
is internally paralleled with its phone input (The TIP of the channel 'A' PHONE input is connected to pin 2 of its XLR
input, the RING is connected to pin 3, and the Sleeve is connected to PIN 1). PIN 2 is in phase, PIN 3 is 180 degrees
out of phase, and PIN 1 is ground.
2. Unbalanced Inputs
Ordinary single circuit Standard 1/4-inch PHONE plugs may be used to connect unbalanced signals.
Push to
Reset
WARNING: SHOCK HAZARD • DO NOT OPEN
AVIS: RISQUE DE CHOC • NE PAS OUVRIR
WARNING: RISK OF HAZARDOUS ENERGY! SEE OPERATING MANUAL.
AVERTISSEMENT: ÉNERGIE ÉLECTRIQUE DANGEREUSE! VOIR LE CAHIER D'INSTRUCTION.
GROUND
STEREO
SUBSONIC
LIMITER
CONNECTED
MODE
FILTER
ENABLE
20 Hz
SUBSONIC
GROUND
MONO
LIMITER
FILTER
Channel
LIFTED
MODE
DEFEAT
40 Hz
NOTE: Such plugs effectively connect the ring terminal to sleeve ground, so they
work correctly. However, if you use a Stereo 1/4-inch PHONE plug on an unbalanced
line, you MUST short the Ring terminal to the sleeve terminal, otherwise the
sensitivity will be 6dB lower than is specified! (The same applies to the XLR input: To
connect an unbalanced source via the XLR input, you must connect the signal to Pin
2 and ground both Pin 1 and Pin 3).
Channel A
-15
-18
-21
Clip
Signal
-30
-0 0
-0 0
0
0
dB
A-Z1128 / 1v1
MODEL TYPE:
YS6040
D O N OT O P ER ATE I N BR I DGE MO D E
D O N OT GRO U ND O UT PU T TE RMI NA L S
S P E A KO N ™ P I N C O N F I G U R AT I O N
TWO CABLES
SINGLE CABLE OUTPUT
B
1+
1+
1+
2+
A
(
)
B
(
)
A / B
(
)
(
)
1–
1–
1–
2–
Ch
2000 WATTS
S P E A K E R O U T P U T S
4-OHMS MIN
Channel B
-15
-18
-12
-12
-9
-9
-21
Clip
-6
-6
-3
Signal
-3
-30
-0 0
-0 0
0
0
dB
MADE IN CANADA
A / B
A
Ch
2000 WATTS
4-OHMS MIN
1
Publicité
Table des Matières
