Allducks MP2110 Manuel D'installation page 9

4-1
With unlocked arch and cover removed, push and hold
the release pin in the lock and manually position the arch
down.
4-2
Position the MyPark to a desired place on your parking spot.
4-3
Using a suitable tool, mark the fi xing positions on the
ground for the anchoring bolts.
4-4
Drill out 2 holes into the ground. The holes should have
12 mm diameter and 100 mm depth.
CAUTION: The anchors included in the kit are intended
for use in hard materials such as concrete,
etc. In case the ground on which the device
will be installed is softer, we recommend
using longer (15 cm) chemical anchors.
4-5
Insert the two anchoring bolts into the previously drilled-
out holes through the MyPark device.
4-6
Tap both anchoring screws with a hammer.
CAUTION: Take great care not to damage any part of
the MyPark device when doing this, especi-
ally the electronic board inside!
4-7
Using a 19 mm hexagonal socket head wrench securely
tighten both anchoring bolts.
5 DELETING THE CODES STORED IN THE ELECTRONIC PANEL
In order to delete the codes stored in the MP20 electronic panel memory, press and hold the P1 button (for approximately 15 sec)
until the red LED fl ashes and turns off. By doing this, all codes are deleted.
CAUTION: By this procedure, all codes stored in the memory will be permanently deleted, and it will not be possible to restore them.
Now, it is necessary to store codes of remote controls which you want to use with this device – see the procedure stated
in points 4-9 to 4-11.
BATTERY LOW CHARGE ALERT SIGNAL
6
In case the batter charge is low, the device indicates this state in the following manner:
When the arch is moving, it will stop at 45° for few seconds and then will continue its movement. When this happens, it is necessary
to recharge the battery using the battery charger supplied with the MyPark device. For details, go to chapter 2 of this manual.
7 WARRANTY & AFTER SALE SERVICE
Allducks products are guaranteed for 24 months from purchase date, for manufacture or material defects. In case of repair, the
product shall be returned to one of our authorized after-sale centres, witch are the only ones authorized to carry out repairs under
warranty. To get your country's after-sales offi ces, please contact us:
Allducks Srl Via, Alessandro Volta, 1 - 20060 Ornago (MI), ITALY, Tel. +39/039/6010654, Fax +39/039/6011243,
service@allducks.it, www.allducks.it
Warranty Terms and Conditions
1. The warranty only covers presented claims with the invoice or coupon proving purchase; no alteration or cancellation shall be on
this certifi cate .
2. Allducks obligations are limited to repair or, at its own discretion, replacement of defective parts.
3. The product warranty shall immediately be voided if the product is modifi ed and adapted to technical and safety standards diffe-
ring from those in force in the country for which the product was conceived and manufactured.
No refund is forthcoming for damages deriving from the above-mentioned modifi cations.
4. The warranty does not cover:
a) Periodical checks, maintenance, repairs or replacement of worn out parts .
b) Transport, handling or installation costs relating to this product.
c) Improper use, mistakes in the operation and incorrect installation.
d) Damages caused by fi re, water, natural phenomena, storms, incorrect power supply, or any other cause not relating directly to
the manufacturer.
8 TROUBLESHOOTING
PROBLEM
The remote control is not working
Low receiving level of signal
Water in the parking case
I cannot see the arch from my car - Ask for our special fl ag, see our web site www.allducks.com
4-8
4-9
4-10
4-11
4-12
4-13
- Check the battery inside the remote control and replace if necessary
- Check the battery inside the MyPark device and recharge if necessary
- Delete all codes from MP20 board and go to point 4-9
- Check the remote control battery or ask for a hard plastic cover (ref.MP002/P) to increase
the receiving signal, see our web site www.allducks.com
- Dry the water and test function of MyPark - go to point 4-7
4
Lock the arch by means of the locking key, see chapter
3 for details.
Press the P1 button on the electronic board MP20. The
red LED (A) lights up.
On the remote control, push that button which you want
to use to operate the device (A=OFF or B=ON) and
release it. The red LED will shortly blink and then will be
continuously lit for some time. After the LED switches off,
the code is memorized in the electronic panel.
NOTE: The maximal capacity of the panel is 10 codes.
Use the remote control to test the function of the MyPark
device. If everything is in order, the arch should rise up. If
not, it is necessary to reintroduce the remote control code
to the electronic board MP20. To do this, please start
again from the point 4-9.
If the device operates correctly, screw the cover back on.
To do this, it is necessary to unlock the arch and position
it to approximately 45°. After reinstalling the cover, posi-
tion the arch to the upper position or lower position and
lock it. For details, see chapter 3.
Your MyPark device is ready to use!
SOLUTION