Installation Manual - Allducks MP2110 Manuel D'installation

1 KIT CONTENTS AND TECHNICAL DATA
The automatic parking post MyPark is supplied packed in a printed carton box having dimensions of 60x40x10 cm. Total package
weight is approximately 10 kg.
Item Name
Automatic parking post, varnished
aluminium casing and steel arch
1
(with cover dismantled)
Rechargeable battery 7A 12V
2
Battery charger
3
Anchoring bolts for concrete
4
Manual locking/unlocking key
5
Remote control
6

Installation manual

7
2 CHARGING THE BATTERY BEFORE INSTALLATION
Although the battery inside the MyPark device is supplied charged, it may loose its capacity e.g. when it is stored for a longer time, etc. Thus
before installing your MyPark device to your parking spot and using it, it is necessary to fully charge the battery. Proceed as follows:
2-1
Position the arch to 45°. To do this, you must unlock the
arch and move it manually - see chapter 3 ARCH UNLOC-
KING AND LOCKING.
2-2
Using a hexagonal wrench, unscrew the four screws from
the cover and slide the cover aside.
CAUTION: Be carefull not to press the control board insi-
de the MyPark!
2-3
Take out the battery and disconnect the two cables.
2-4
Connect the charger cables to the battery and plug the
charger to a standard 230V socket.
CAUTION: Respect the polarity of the cables!
 (plus) = Red cable
 (minus) = Black cable
ARCH UNLOCKING AND LOCKING
3
3-1
: WHEN THE ARCH IS DOWN
A
UNLOCKING
Insert the key into the position -90°, turn it clockwise to 0°
and remove the key. Proceed to point 3-3.
B
LOCKING
Insert the key into the position 0°, turn it counterclockwise
to -90° and remove the key.
4 INSTALLATION OF THE MYPARK DEVICE
ATTENTION: The installation of the MyPark device requires a fully charged battery inside the device. In case it is not charged, please
refer to chapter 2.
It is assumed that the MyPark device is in the state as descibed in point 2-7 of chapter 2.
Qty. Ref.No.
Inside: 12V 3W DC motor, microprocessor controlled electronic
board, limit switches for open/close position, reverse system, ob-
stacle detection system and automatic battery voltage indicator.
1x
MP2110R
IP67 water tight.
On arch: Lockable key-switch for manual arch lowering/rising
Dimensions: (height x length x width - 54x45x40 mm
1x 7A battery with consumption of 0,0007 A in stand-by
MPBATTSLIM
1x State check and LED indicator
MP037
2x 12 mm diameter, 100 mm length
MP039
2x --
MP054
433,92MHz, two buttons rolling code transmission protocol (billi-
1x
623 ROLLRED
ons of combinations)
1x --
MP035
2-5
Charging process (A) is indicated by a red light on the
charger. A fully charged battery is indicated by a green
light (B). After the battery is charged, unplug the char-
ger from the mains and disconnect it from the battery.
2-6
Reconnect the cables of the MyPark device to the battery
while respecting the polarity of the cables. Insert the batte-
ry inside the device.
CAUTION: Respect the polarity of the cables!
2-7
Continue with the installation of the MyPark device accor-
ding to chapter 4.
3-2
: WHEN THE ARCH IS UP
A
UNLOCKING
Insert the key into the position 0°, turn it clockwise to +90°
and remove the key. Proceed to point 3-3.
B
LOCKING
Insert the key into the position +90°, turn it countercloc-
kwise to 0° and remove the key.
3-3
Push and hold the lock release pin using a fi nger of one hand.
Using the other hand, move the arch freely up or down.
3
Technical Data
 (plus) = Red cable
 (minus) = Blue cable