Table des Matières
Publicité
• Operating the tool 0
- lower spark guard A as far as possible
- switch on tool
- lay the workpiece to be ground on tool rest C
- move the workpiece lightly from the left to the right
and back (for optimal grinding results as well as
uniform wear of the grinding wheel)
- cool the workpiece in water from time to time
- switch off tool
• Replacing grinding wheels !
! disconnect the plug
! use only grinding wheels with an allowable speed
matching at least the highest no-load speed of
the tool
! use only original SKIL grinding wheels with a
maximum thickness of 20 mm and a spindle hole
diameter of 16 mm
- remove protective cover G by loosening
(not removing) the 3 screws B
- unscrew clamping nut H with a spanner 19
- remove clamping fl ange J and grinding wheel
- for mounting new grinding wheel handle in reversed
order
! perform a sound-test on new grinding wheels and
test-run them without load for at least 5 minutes
(stay out of danger area)
MAINTENANCE / SERVICE
• Always keep tool and cord clean
• Protect the tool from impact, shock and grease
• Keep grinding wheels in a dry place where the
temperature is as constant as possible
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol @ will remind you of this when the need for
disposing occurs
CE DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 61 029, EN 55 014, in
accordance with the provisions of the directives
2006/95/EC, 2004/108/EC, 98/37/EC (until Dec. 28,
2009), 2006/42/EC (from Dec. 29, 2009 on)
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
09
SKIL Europe BV
NOISE
• Measured in accordance with EN 61 029 the sound
pressure level of this tool is 86 dB(A) and the sound
power level 99 dB(A) (uncertainty: 3 dB)
F
Meuleuse d'établi
INTRODUCTION
• Lisez attentivement ce manuel d'instruction avant
d'utiliser l'appareil et conservez-le pour pouvoir vous y
référer ultérieurement 3
• Cet outil est une machine fi xe, conçue pour l'aiguisage
d'outils manuels, ainsi que pour le meulage et
l'ébarbage du métal
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Pare-étincelles réglable
B Vis du revêtement de protection
C Porte-outil réglable
D Trous de fi xation
E Appui en caoutchouc (4x)
F Interrupteur marche/arrêt
G Revêtement de protection
H Écrou de serrage
J Bride de serrage
SECURITE
INSTRUCTIONS GENERALES DE SECURITE
ATTENTION! Lisez tous les avertissements de
sécurité et toutes les instructions. Ne pas suivre les
avertissements et instructions peut entraîner un choc
électrique, un incendie et/ou de graves blessures sur les
personnes. Conservez tous les avertissements et
toutes les instructions pour pouvoir s'y reporter
ultérieurement. La notion d'"outil électroportatif" dans les
avertissements se rapporte à des outils électriques
raccordés au secteur (avec câble de raccordement) et à
des outils électriques à batterie (sans câble de
raccordement).
8
A. v.d. Kloot
3900
Publicité
Table des Matières
