Software Version; System Reset; Backlight; Bluetooth Led - PERFECTPRO SLIM-3 Manuel De L'utilisateur

SOFTWARE VERSION

The software display cannot be altered and is just for your reference. You can only view
the software version in DAB, FM or Bluetooth mode.
1. Press the ON/OFF button to switch on the radio.
Press the SOURCE button to select FM or DAB, or Bluetooth mode.
2.
3. Press the MENU button until the display shows "Full Scan" at DAB, or "Scan
setting" at FM, or "Disconnect BT" at Bluetooth mode, and then rotate the TUNING/
SEEK knob until the display shows "System".
4. Press the TUNING/SEEK knob; rotate the TUNING/SEEK knob until the display
shows "SW version".
5. Press the TUNING/SEEK knob to view the software version.
6. Press the TUNING/SEEK knob back to the last menu, and press the TUNING/
SEEK knob again to return to the normal radio display.
Notes: USB socket inside battery compartment is for upgrading the software of the
device.

SYSTEM RESET

If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the ON/OFF button to switch on the radio.
2. Press the MENU button,
3. Rotate the TUNING/SEEK knob until the display shows "System". Press the
TUNING/SEEK knob.
4. Rotate the TUNING/SEEK knob until the display shows "Factory reset". Press the
TUNING/SEEK knob.
5. Rotate the TUNING/SEEK knob to select between "Yes" or "No".
Select "Yes" if you wish to reset the radio; otherwise, select "No" to cancel the
selection.
6. Press the TUNING/SEEK knob to cause the factory reset.
7. A full reset will be performed. All presets and the station list will be erased. All
settings will be set to the default values.
The display will show "WELCOME TO DIGITAL RADIO" for a few seconds, and
then the radio will automatically perform an auto scan of the Band III DAB channels
and the FM band.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
remove and reconnect the power supply.
23

BACKLIGHT

LCD backlight configuration
1. Press the ON/OFF button to turn on the radio.
Press the MENU button, and then rotate the TUNING/SEEK knob until the display
2.
shows "System".
3. Press the TUNING/SEEK knob; rotate the TUNING/SEEK knob until the display
shows "LCD backlight".
4. Press the TUNING/SEEK knob to enter the LCD backlight adjustment menu.
5. Rotate the TUNING/SEEK knob to select "on" in order to keep backlight always
lightened when the radio is turned on with AC power supply;
6. Or rotate the TUNING/SEEK knob to select "off" (by default) so that the backlight
will be lightened for about 10 seconds whenever a button is pressed with AC power
supply.
7. Press the TUNING/SEEK knob to confirm your choice.
Note: The LCD backlight option "on" is only functional when the radio is powered by AC
power supply. When the radio is powered by battery power supply, the LCD backlight
is switched to option "off" – 10 seconds lightened when a button is pressed. When the
radio is connected to mains AC power again, the last user setting will be applied again.

BLUETOOTH LED

Bluetooth LED configuration
Press the ON/OFF button to turn on the radio.
Press the MENU button, and then rotate the TUNING/SEEK knob until the display
shows "System".
Press the TUNING/SEEK knob; rotate the TUNING/SEEK knob until the display shows
"Bluetooth LED".
Press the TUNING/SEEK knob to enter the Bluetooth LED adjustment menu.
Rotate the TUNING/SEEK knob to select "on" in order to keep backlight always
lightened when the radio is turned on with AC power supply;
Or rotate the TUNING/SEEK knob to select "off" (by default) so that the backlight will be
lightened for about 10 seconds whenever a button is pressed with AC power supply.
Press the TUNING/SEEK knob to confirm your choice.
Note: The Bluetooth LED option "on" is only functional when the radio is in Bluetooth
mode. If the Bluetooth LED option is set to "off", this blue LED will be turned off either
mobile phone is connected (not blinking) or not connected (blinking).
GB
24