PowerA MOGA XP5-X Manuel De L'utilisateur page 3

SETUP
For best results, fully charge controller and power bank prior to first use.
CHARGING CONTROLLER + POWER BANK
• Using the included 6.6ft (2 m) USB Cable, connect the Micro-USB end to lower port at top of the
controller, and connect the Standard USB end to any powered USB source.
• When charging, four LEDs will display the charging level from 25-50-75-100%.
CHARGE LEVEL INDICATOR
Check battery charge level by pressing the battery status button ( ) on front lower left of
controller. The LEDs will indicate the current charge level from 25-100% even when controller is off.
WIRELESS MODE
Move Wireless/Wired switch on front center of controller to BT ( ) which indicates Bluetooth
wireless mode.
• If controller is off, press the Xbox button ( ) to turn on (LED will illuminate).
• Press and hold the Bluetooth sync button ( ) on back of controller for 2 seconds to enter
pairing mode (LED will flash rapidly).
• Enter the Bluetooth settings on your device and choose the MOGA controller. The pairing LED will
turn solid when connected.
NOTE: A previously paired device will automatically pair to the controller when powered on.
POWERING OFF
Hold the Xbox button ( ) for 5 seconds to turn controller off and save battery capacity.
WIRED MODE
Move Wireless/Wired switch on front center of controller to USB ( ) which indicates wired
mode.
• Connect Micro-USB end of the 11.8" (30 cm) or 6.6ft (2 m) cable to lower port at top of
controller, and connect other end to your gaming device.
• Gaming device input ports (Standard USB, Micro-USB, USB-C) will determine whether you use
shorter or longer micro-USB cable for wired gaming.
• This MOGA controller supports DirectInput by default, but also supports XInput mode. If initial wired
connection is unsuccessful, switch modes by pressing Start + Select for three seconds. Three LED
flashes indicate mode was changed and retained in memory. Repeat process to switch back.
GAMING CLIP
A detachable gaming clip is included for use with gaming on your phone. You can use USB cables
with clip attached for charging or wired mode.
1. Slide Xbox Wireless Controller into Mobile Gaming Clip by tipping top edge in first.
2. Push controller bottom edge down into clip until it locks into place.
3. There are two adjustable articulation dials on the Mobile Gaming Clip. Rotate dials in opposite
directions to loosen and adjust position. Rotate dials back to tighten after reaching desired
viewing angle.
4. To insert phone, push top edge of phone against top of phone grip to expand upward.
5. Push bottom of phone down flat into place as you reach top limit of phone grip. Adjust phone
horizontally as needed to center over controller.
6. Remove clip by pulling front edge forward to release from notch.
INTEGRATED POWER BANK
A Power Bank built into the controller allows you to charge your phone during gameplay or while
controller is off.
• Connect Standard USB end of the 11.8" (30 cm) cable to upper port at top of controller, and
connect other end to your mobile device.
• During gameplay, move the Power Bank switch below right thumbstick to the right (on) to start
charging. If you prefer to use battery power to extend controller usage time rather than charge
phone, move swith to the left (off).
• To charge mobile device when controller is not in use, simply connect cable between controller
and device to begin charging (Power Bank Switch must be ON).
• Your mobile device will display charge status once connected. If charging does not begin, the
power bank battery may be too low: recharge controller.
• The amount of charge available for your phone depends on how much battery capacity remains
on the controller when charging begins.
ASSIGNING THE ADVANCED GAMING BUTTONS
1. Press the Green Program Button on the bottom of the controller for 2 seconds. The LED
Connection Indicator will flash, signaling the controller is in assign mode.
2. Press 1 of the following buttons (A/B/X/Y/LB/RB/LT/RT/Left Stick Press/Right Stick Press/D-
pad) to re-assign. Then press the Advanced Gaming Button (AGR or AGL) that you wish to assign.
The LED connection indicator will stop flashing, signaling the Advanced Gaming Button has
been set.
3. Repeat for the remaining Advanced Gaming Button.
Note: Advanced Gaming Button assignments will remain in memory even after disconnected.
RESETTING THE ADVANCED GAMING BUTTONS
1. Hold the Program Button down for 2 seconds. The LED Connection Indicator will slowly flash,
signaling the controller is in assign mode.
2. Press the previously assigned button for 5 seconds, and the function will be cleared.
FAQS
For latest FAQs, visit PowerA.com/Support
PROBLEM: My controller will not power on?
SOLUTION: Confirm the controller is fully charged by pressing the battery status button ( ) on
front lower left of controller. Plug in to recharge as needed.
PROBLEM: I do not see MOGA controller listed in mobile devices Bluetooth settings?
SOLUTION: Press and hold the Bluetooth sync button ( ) on back of controller for 2 seconds to
enter pairing mode (LED will flash rapidly).
PROBLEM: The integrated power bank is not functioning?
SOLUTION: Confirm the controller has more than 25% charge and Power Bank button is switched on.
CONTACT/SUPPORT
For support with your authentic PowerA accessories, please visit PowerA.com/Support.
MANUFACTURED BY
Bensussen Deutsch & Associates, LLC. (BDA, LLC.)
15525 Woodinville-Redmond Rd. NE Woodinville, WA 98072. BDAINC.com | POWERA.com
ADDITIONAL LEGAL
MOGA, the PowerA logo, and the MOGA by PowerA logo are trademarks of Bensussen Deutsch and
Associates, LLC. TM and © Bensussen Deutsch and Associates, LLC. All other trademarks are the
property of their respective owners.
MOTION WARNING
Playing video games can make your muscles, joints, skin or eyes hurt. Follow these instructions to
avoid problems such as tendinitis, carpal tunnel syndrome, skin irritation or eyestrain:
• Avoid excessive play. Take a 10 to 15-minute break every hour, even if you don't think you need
it. Parents should monitor their children for appropriate play.
• If your hands, wrists, arms or eyes become tired or sore while playing, or if you feel symptoms such
as tingling, numbness, burning or stiffness, stop and rest for several hours before playing again.
• If you continue to have any of the above symptoms or other discomfort during or after play,
stop playing and see a doctor.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable