General Safety Instructions - Facom V.DG300F Notice Originale

EN
This precision-built tool, is designed for professionals for grinding and deburring operations in confined areas.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
The pneumatic machine can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
machine if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Do not carry the tool by the hose.
Keep body stance balanced and firm. Do not
overreach when operating this tool.
Do not use the tool under the influence of drugs,
alcohol, medication or if you are tired.
READ THIS MANUAL BEFORE OPERATING THE MACHINE.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION IN THIS MANUAL
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

GENERAL SAFETY INSTRUCTIONS

Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As
appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The
dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high
intensity noise may cause hearing loss. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting
operation is dusty.
• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in
serious personal injury.
• Prevent unintentional starting. Ensure the switch is in the off position before connecting to air source and/or battery pack, picking
up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on
invites accidents.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly
used. Use of dust collection can reduce dust related hazards.
• Keep hands, loose clothing and long hair away from rotating end of tool.
• Anticipate and be alert for sudden changes in motion during start up and operation of any power tool.
• Do not operate this tool for long periods of time. Vibration caused by tool action may be harmful to your hands and arms. Stop
using any tool if discomfort, tingling feeling or pain occurs. Seek medical advice before resuming use.
• Use rated accessories recommended by FACOM only. Inspect accessories before use. Do not use cracked or damaged
accessories. Just because the accessory can be attached to your power tool, it does not assure safe operation.
• Do not operate this tool in the presence of flammable liquids, gasses, dust, or explosive atmospheres.
• This tool is not insulated against electric shock, contact with a live wire will make exposed metal parts live.
• Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this
tool, or before performing any maintenance on this tool.
• For safety, top performance, and maximum durability of parts, operate this tool at 90 psig (6.2 bar / 620 kPa) maximum air pressure
at the inlet with 3/8'' (10mm) inside diameter air supply hose.
NU-V.DG300F V.DGE300F V.DGA305F V.DGA310F_0715M.indd 7
WARNING
IMPORTANT SAFETY INFORMATION ENCLOSED.
INTO THE HANDS OF THE OPERATOR.
Use protective equipment such as glasses, gloves,
safety shoes as well as acoustic protection.
Remain vigilant, use common sense and pay
attention when using the machine.
Always turn off the air supply and disconnect
the airsupply hose before installing, removing or
adjusting any accessory on this machine, or before
performing any maintenance on this tool.
Operate at 90 psig (6,2 bar / 620 kPa) Maximum
pressure.
SAVE FOR FUTURE REFERENCE.
7
9/3/2015 3:24:25 PM