Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
• PLAYING CD-R and CD-RW:
Apart from normal audio CD's the MCD150 can play both CD-R (CD recordable) and
CD-RW (CD rewriteable). Please note that you should always use the "disc at once" and
"track at once" disc writing options! Burning your CD's at speeds higher than 12x can
cause reading errors. If the disc is multi session, it will only play the first session:
• if the first session is CD-DA you can only play CD-DA tracks.
• if the first session is MP3 you can only play MP3 files.
• SLEEP MODE:
The CD player automatically shuts off the transport and laser after about 15 minutes
(when in pause or cue mode). This extends the life of your motor drive and laser. During
sleep mode the display shows the word "SLEEP". To wake up the player, just press the
cue or play button, the display turns to normal and is ready to receive instructions.
• CREATE A LOOP:
While a track is playing, press IN/R.CUE button to program the starting point of the loop.
Now press the OUT/EXIT button to program the endpoint of the loop. The seamless loop
starts playing at once. (With some practice you will be able to create perfect loops!)
While the loop is playing, you can press the OUT/EXIT button again to exit the loop and
continue the rest of the track.
It is possible to program a new loop, even when the current loop is still playing. While the
loop is playing, simply press the IN/R.CUE button to set the starting point of the new
loop. Now enter the endpoint by pressing the OUT/EXIT button. Your new loop is
programmed and playing.
• RESTART A LOOP:
This can be done in 2 ways:
• When a loop is programmed and you left it by pressing the OUT/EXIT button, just
press this button again to restart the loop.
• When the loop is still playing, press the CUE button to restart the loop immediately.
You can repeat this several times to create a "Stutter" effect.
• STORING A CUE POINT:
There are 2 ways to set a cue point:
• Press the IN/R.CUE button during normal playback to set the new cue point ("CUE on
the fly").
• Put the player in pause and use the search buttons (9) to search for the exact
location for the cue point. Once this location is found, press "IN/R. CUE" button to set
the new cue point. (or press PLAY/PAUSE button)
Once the cue point is programmed, just press the CUE button to recall it.
• PITCH BENDING:
This function is used to put the beats of two tracks in perfect sync. The speed increases
or decreases respectively as long as the PITCH BEND+ or PITCH BEND- button is
pressed.
JB SYSTEMS
®
OPERATION MANUAL
7/25
MCD150
ENGLISH
SPECIFICATIONS
Power Supply:
AC 230 V, 50Hz
Power Consumption:
17W
Output level:
2,0Vrms +/0.5dB @ 1kHz, 0dB
Frequency response:
20-20.000Hz (+/-0,4dB)
THD + noise (20kHz LPF):
0,01% @ 1kHz, 0dB
S/N Ratio (IHF-A):
>92dB @ 1kHz, 0dB
Short access time (next track):
<2sec
Long access time (track 1
20):
<4sec
Laser Pickup:
Sony KSM-213CCM 3spot detection 780nm
Electronic tracking:
Full automatic digital tracking.
DISC FORMAT:
Possible file extensions:
.mp3 ~ .MP3 ~ .mP3 ~ .Mp3
ISO9660:
max. 63 character style
Joliet:
max. 63 character style
CD-ROM sector format:
mode-1 only
Max. Folders:
255
Max. Files:
999
MP3 FORMATS:
MPEG1 Layer3 (ISO/IEC11172-3):
mono / stereo sampled at: 32 - 44,1 - 48kHz
Bitrates:
32 – 320 Kbps
Bitrate modes:
CBR (Constant Bitrate) or VBR (Variable Bitrate)
MPEG2 Layer3 (ISO/IEC13818-3):
mono / stereo sampled at: 16 – 22,05 - 24kHz
Bitrates:
32 – 160 Kbps
Bitrate modes:
CBR (Constant Bitrate) or VBR (Variable Bitrate)
MPEG2,5 Layer3:
mono / stereo sampled at: 8 – 11,025 - 12kHz
Bitrates:
32 – 160 Kbps
Bitrate modes:
CBR (Constant Bitrate) or VBR (Variable Bitrate)
Dimensions:
216(W) x 96(H) x 274(D) mm
Weight:
1,7kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS
®
OPERATION MANUAL
8/25
MCD150
Publicité
Table des Matières
