Optional Accessories - Oleo-Mac PW 175C Manuel D'utilisation Et D'entretien

• service centres booklet;
• nozzle hexagonal key;
• nozzle cleaning pin.
If there are problems, contact your dealer or an authorised assistance centre.
The following range of accessories can be added to the standard high-pressure cleaner equipment:
• rotating nozzle lance: designed for the removal of stubborn grime (standard on
• sandblasting lance: designed for sanding surfaces, removing rust, paint, incrustations, etc.;
• rotating water jet brush: designed for cleaning delicate surfaces;
• fixed water jet brush: designed for cleaning delicate surfaces. (standard on
• Pipe flushing probe: designed for unblocking pipes and ducts;
• floor cleaning lance;
• high pressure hose extension kit 8 m/26 ft: ideal for increasing the cleaning surface;
In order to prevent damages to the high pressure cleaner, the following operations should be done
by two persons.
• Carefully IP 1900 S - PW 190 Cct the high pressure washer from the carton box, paying attention not to
damage it or let it fall down.
• Insert till the end the foot (27) on the high pressure washer frame, checking the correct positioning.
.
PICT. 4b
• Lock the foot with the 2 screws supplied (cross screew driver not supplyed).
• Mount the wheel (24), until you hear a "click".
• Insert till the end the Hose reel knob (21).
• Mount and push till it's completely locked the handlebar (3). Double check that the handlebar is completely
insered into the machine frame (frontal surfaces must be aligned). Lock the handlebar with the 2 screws
supplied (cross screw driver not supplied).
• Screw the high-pressure pipe connector (23) to the thread of the gun (14) and fully tighten with a 17 mm/0,67
in spanner (not supplied).
• Take the high pressure water cleaner to the work position, getting hold of its handle (2).
the lifting handle (10) and handlebar (3) for lifting
• Completely unreel the high pressure hose (23).
• Insert the high pressure hose quick coupler (30) on the outlet coupling (29), and fully tighten the ring nut
by hand (only
IP 1750 S - PW 175 C
• Seecure a supply hose to the quick-release water inlet fitting (12) using a general-purpose gardening
quick-release fitting.
• Open the water supply tap, making sure there is no dripping.
• Make sure the main ON/OFF switch (2) is turned to "0" and connect the plug
• Turn the main ON/OFF switch (2) to position "1".
• Press the lever (26) of the high pressure water cleaner and wait for water to flow out continuously
• Switch the main ON/OFF switch (2) to position "0" and connect the spray lance (15) or (18) to the water
gun (14), tightening firmly.
• Check that the nozzle head (16) is not in the detergent distribution position (see also paragraph
WITH DETERGENT"
• Re-start the high pressure water cleaner again, switching the main ON/OFF switch (1) to position "2".
when starting in this phase, the high pressure water cleaner will stop immediately after the starting
NOTE:
14
breakaway because the

OPTIONAL ACCESSORIES

INSTALLATION AND ACCESSORIES ASSEMBLING
SEE PICT. 4a
OPERATION A - PICT. 9
OPERATION - PRELIMINARY OPERATIONS
).
SEE PICT. 1.
OPERATION B - PICT. 9
OPERATION E - PICT. 9
STANDARD OPERATION (AT HIGH-PRESSURE)
).
device trips.
TOTAL STOP
.
.
SEE PICT. 4d
.
SEE PICT. 4e
.
SEE PICT. 4f
SEE PICT. 6.
.
OPERATION C - PICT. 9
.
IP 1900 S - PW 190 C
IP 1900 S - PW 190 C
.
SEE PICT. 4c
SEE PICT. 5
.
OPERATION D - PICT. 9
"OPERATION
);
);
SEE
. Use
.