Fusion Ms-Nrx300 Installation Instructions - Fusion MS-NRX300 Instructions D'installation

FUSION MS-NRX300
®
Installation Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information
guide in the product box for product warnings and
other important information.
CAUTION
Always wear safety goggles, ear protection, and a
dust mask when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the
opposite side of the surface.
Getting the Owner's Manuals
To fully understand the features and operations of
your stereo, you can get the latest stereo owner's
manual and translations of manuals from the web.
You can also download the full remote owner's
manual for more information about using this remote.
1
Go to www.fusionentertainment.com/marine.
2
Select the product.
3
Select Manuals & Downloads.
4
Select a manual.
Tools Needed
• Phillips screwdriver
• Drill
3
• 2.5 mm ( / in.) drill bit
32
• 50 mm (2 in.) hole saw
• Marine sealant (optional)
Connection Considerations
You can connect the MS-NRX300 remote control to
the FUSION stereo using a FUSION remote control
network or an existing NMEA 2000
depending on the stereo. Some stereo models
support the powered NMEA 2000 network connection
only.
You may need to obtain a red, NMEA 2000 Power
Cable (CAB000541) and an additional NMEA 2000 T-
connector (CAB000581) to create a NMEA 2000
network.
Remote Control Network Connection
Considerations
You can connect the remote control to the stereo
using an unpowered remote control network if you
have the following conditions.
• You do not have a full NMEA 2000 network on
your boat.
• You are connecting three or fewer MS-NRX300
remote controls to one FUSION stereo.
• You are connecting to a FUSION stereo that
provides power to the remote, such as a FUSION
MS-UD650, MS-AV650, MS-UD750, MS-AV750,
MS-BB300, or MX-RA205 stereo.
• You are not connecting to a FUSION stereo that
does not provide power to the remote, such as a
FUSION MS-BB100 or MS-RA70 stereo.
When connecting the MS-NRX300 remote control to
an MS-UD650, MS-AV650, MS-UD750, or MS-
AV750 stereo using the unpowered remote control
network, you must use the cable located in the wiring
harness at the rear of the stereo. When connecting
the MS-NRX300 remote control to an MS-BB300 or
MX-RA205 stereo using the unpowered remote
control network, you must use a red, powered drop
2
cable (CAB000862). You do not need to connect the
remote control network to another power source.
NOTE: When connecting to an MS-UD650, MS-
AV650, MS-UD750 or MS-AV750 stereo through a
remote control network, you must enable the NRX
POWER setting to provide power to the remote
control. Select
Item Description
FUSION stereo
MS-NRX300 remote control
WIRED REMOTE cable from the stereo wiring
harness or red, powered drop cable (CAB000862)
NMEA 2000 female terminator
NMEA 2000 T-connector (CAB000581)
NMEA 2000 backbone cable, 6 m (20 ft.)
NMEA 2000 inline terminator
NMEA 2000 Connection Considerations
You can connect the remote control to the stereo
using a powered NMEA 2000 network if you have a
powered and properly balanced NMEA 2000 network
on your boat or you have these conditions.
• You are connecting more than three MS-NRX300
remote controls to one FUSION stereo.
• You are connecting to a FUSION stereo that does
not provide power to the remote, such as a
FUSION MS-BB100 or MS-RA70 stereo.
An unlimited number of MS-NRX300 remote controls
can be connected to the NMEA 2000 network.
Through the NMEA 2000 network, you can control a
connected FUSION stereo on compatible devices,
network,
®
such as the MS-NRX300 remote control and
compatible chartplotter.
Item Description
FUSION device
Compatible chartplotter
MS-NRX300 remote control
12 Vdc power source with an ignition or in-line
switch
FUSION NMEA 2000 drop cable
This can be extended to a maximum length of 2 m
(6 ft.) using a standard NMEA 2000 cable.
NMEA 2000 drop cable
MS-NRX300 remote control drop cable.
This can be extended to a maximum length of 2 m
(6 ft.) using a standard NMEA 2000 cable.
NMEA 2000 power cable, 2 m (6 ft.) (CAB000541)
NMEA 2000 terminator or backbone cable
NMEA 2000 T-connector (CAB000581)
Mounting Considerations
When selecting a mounting location, observe these
considerations.
> SETTINGS > NRX POWER.
Installation Instructions