Ryobi SUPERCHARGER P125 Manuel D'utilisation page 6

NOTE: The LED charge indicator light will not work if the
battery protection feature has caused the battery pack to
stop powering the tool. When the battery pack resets itself,
the LED will again function.
LED FUNCTIONS OF CHARGER
See Figures 4 - 5, pages 9 - 10.
BLUE LED STATUS BUTTON
Charger has blue LED status button to indicate power on .
Refer to chart on page 9.
 When batteries are charging , the blue LED status button
will maintain a full and constant brightness.
 While batteries are in maintenance mode, the blue LED
status button will slowly pulse. When maintenance mode
is complete, charger goes into energy save mode.
 Blue status button will maintain a fluctuating pulse while
in energy save mode. When batteries are not being
charged, maintained or when the charger does not hold
any batteries.
NOTE: Battery port LEDs will turn off during maintenance
mode and energy save mode.
 Charger awakens from energy save mode when status
button is pressed or automatically after 5 days in energy
save mode.
BATTERY PORT LEDS
 Red LED on, Green LED off = Battery installed.
 Red LED flashing, Green LED off = Battery is being
tested.
 Red LED on, Green LED flashing = Battery is charging.
 Red LED off, Green LED on = Battery is fully charged.
 Red LED flashing, Green LED flashing, simultaneously =
Battery is defective.
 Red LED flashing, Green LED flashing, alternating =
Battery port is defective.
CHARGING THE BATTERY PACK
This charger will accept Ryobi One+ 18 V lithium-ion
battery packs and Ryobi One+ 18 V nickel-cadmium battery
packs.
Use only Ryobi One+ 18 V battery packs with this
charger:
BATTERY PACK
(P104 Li-ion)
130429001,
130429002,130155001
(P103 Li-ion)
130429004
(P100 Ni-Cd)
130255004, 130224028
OPERATION
CHARGER (P125)
140108001
6 — English
CHARGING A BATTERY PACK
If the charger does not charge the battery pack under normal
circumstances, take both the battery pack and charger to your
nearest Authorized Service Center for electrical check.
 Use battery pack only with the recommended charger.
 Connect the charger to the power supply. Make sure the
power supply is normal household voltage, 120 volts,
AC only, 60 Hz.
 Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured in the
charger before beginning operation.
 Place the battery pack in the charger aligning raised rib
on the battery pack with the groove in the charger.
 Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
 Do not place the charger and battery pack(s) in an area
of extreme heat or cold. They will work best at normal
room temperature.
NOTE: The charger and battery pack(s) should be placed
in a location where the temperature is more than 50°F
but less than 100°F.
 The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
 After charging is complete, the green LED will remain
on until the battery pack is removed from the charger or
charger is disconnected from the power supply or until
charger enters maintenance mode/energy save mode.
 To remove the battery pack(s) from the charger, depress
the latches on each side of the battery pack.
CHARGING A HOT BATTERY PACK
If the battery pack is above normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery pack cools down to approximately 122°F,
the charger will automatically begin fast charge mode.
CHARGING A COOL BATTERY PACK
If the battery pack is below normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery warms to a temperature of more than
32°F, the charger will automatically begin charge mode.
COLD WEATHER OPERATION
The lithium-ion battery pack can be used in temperatures
down to -4°F. Put the battery pack on a tool and use the
tool in a light duty application. After about a minute, the pack
will have warmed up and begin operating normally.