Declaration Of Conformity; Specified Use; General Safety Instructions; Special Safety Instructions - Metabo SSP 1000 Notice D'utilisation Originale

Original instructions

1. Declaration of Conformity

Under our sole responsibility, we hereby declare
that these compressed-air sand blasting guns/
compressed air combo-spray guns/compressed air
spray guns, identified by type and serial number *1),
meet all relevant requirements of directives *2) and
standards *3). Technical documents for *4) - see
Page 3.

2. Specified Use

SSP 1000: This compressed air sand blasting gun
is intended for the removal of rust and paint/varnish
on metal and wood-based materials using a suit-
able abrasive.
SPP 1000: This compressed air spray gun is
intended for injecting and spraying cleaner
solvents, cleaning agents and spray oils as well as
for waxing, sealing and impregnating in the profes-
sional sector.
UBS 1000: This compressed air combo-spray gun
is intended for spraying cavity sealing and under-
coating in the professional sector and can be used
with standard, commercial screw cartridges.
The compressed air used must be cleaned and be
free of condensate and oil.
This air tool must only be operated with a com-
pressed air supply. The maximum supply pressure
specified on the air tool must never be exceeded.
The tool must not be operated using explosive, in-
flammable or hazardous gases. It must not be
used as a lever, crushing tool or striking tool.
Any other use does not comply with the intended
purpose. Unspecified use, modification of the air
tool or use of parts that have not been tested and
approved by the manufacturer can cause unfore-
seeable damage.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention regula-
tions and the enclosed safety information must be
observed.

3. General Safety Instructions

For your own protection and for the
protection of your air tool, carefully
observe all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety warn-
ings and instructions may result in electric shock,
fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your air tool only together with these docu-
ments.
- The user or user's employer must evaluate the
specific risks associated with each application of
the tool.
- The safety instructions must be read and under-
stood before installing, operating, repairing or
maintaining the tool, and also before replacing any
accessory parts or carrying out any work in the
vicinity of the air tool. Failure to read and follow the
instructions may lead to serious injury.
- Only qualified, trained operators are authorised to
install, adjust or use the air tool.
- The air tool must not be modified. Any modifica-
tions implemented may reduce the efficiency of
the safety measures and increase risks for the
operator.
- Never use air tools that have been damaged. Look
after your air tools carefully. Regularly check that
all moving parts are functioning correctly and do
not jam. Also ensure that no parts are broken or
damaged to an extent that they affect the opera-
tion of the air tool. Check that all signs and labels
are legible and intelligible. Have damaged parts
repaired or replaced before using the device.
Many accidents are caused by poorly maintained
air tools.

4. Special Safety Instructions

4.1 Risks associated with ejected parts
- If either accessory parts or the air tool breaks,
parts may be ejected at high speed.
- While operating, maintaining or repairing the air
tool, or replacing accessory parts, you must
always wear impact-resistant safety goggles. The
degree of protection required for each individual
task must be evaluated separately in each case.
- Ensure that the workpiece is securely attached.
- Disconnect the air tool from the compressed air
supply before replacing the mounted tool or
accessories, and also before carrying out mainte-
nance, settings or cleaning.
- Also ensure that no other people are placed at
risk.
4.2 Risks during operation
- The operator and maintenance staff must be
physically capable of handling the size, weight
and power output of the air tool.
- Ensure you are standing in a safe position and
keep your balance at all times.
- Avoid accidental operation. If the air supply is
interrupted, switch off the air tool using the On/Off
switch.
- Wear personal protective equipment and always
wear safety glasses. By wearing personal protec-
tive equipment such as gloves, protective
clothing, a dust mask, non-skid safety shoes, a
safety helmet or ear protectors, to suit the type of
device and its use, you reduce the risk of injury.
Wearing this equipment is recommended.
ENGLISH en
9