DeWalt DXSTA04MP Guide D'utilisation page 2

• Be cautious of sharp edges.
• Ensure that the rack is level.
• Keep this information for further reference.
Assembly Instructions (Fig. 1-3)
NOTE: Having an assistant to help install the mounting plates to the
rack makes the process safer and easier.
NOTE: It is recommended that all (4) mounting plates are used
during installation.
1. Using a screwdriver and a rubber mallet, remove all four black caps
from the bottom of the assembled rack.
2. Thread a single securing nut onto the stud of the mounting plate.
Then slide on the upright beam support bracket. Ensure that the
tabs of the upright beam support bracket are pointing up. (Fig. 1)
3. Insert a securing tab into the bottom slot of the upright beam. Then,
slide the stud of the mounting plate into the hole of the securing tab
through the bottom of the rack's upright beam. Position the upright
beam support bracket to fit around the upright beam of the rack and
then thread on a securing nut. (Fig. 2-3)
4. Repeat this process for each leg of the upright beams.
FIG. 1
UPRIGHT BEAM
SUPPORT
BRACKET
(TABS POINTING UP)
SECURING
NUT
MOUNTING
PLATE
FIG. 3
BACK
SIDE OF
UPRIGHT
BEAM
FIT
BRACKET
SECURING INTO
NUT BEAM
SECURING
TAB
Leveling Instructions (Fig. 4-6)
NOTE: Having an assistant to help install the mounting plates to the
rack makes the process safer and easier.
NOTE: It is important to ensure that the rack is level. Residing on an
uneven surface can cause twisting and can compromise the rack's
strength and rigidity. An improperly leveled rack poses an increased risk
of tipping over which can result in serious injury or death.
NOTE: Mounting plates allow up to 7 in (17.78 cm) of height adjustment
to help properly level the rack before proceeding to secure the mounting
plates to a floor or the rack to the wall.
NOTE: To ensure better stability, it is advised to use as little height
adjustment as possible to level the rack.
1. Adjustments to the levelness of the rack is done by using the
securing nuts to move the stud of the mounting plates. Begin by
adjusting all four (4) mounting plates so that they are approximately
the same. (Fig. 4)
2. Use a large level to check the levelness of the rack by placing it on a
crossbeam or shelf. Make adjustments as required to level the rack.
Never allow the stud of the mounting plate to be recessed into the
top securing nut (Fig. 5); the stud must always protrude by three or
more threads (Fig. 6).
WARNING: Ensure that the rack is level. Serious injury or death
can occur from the rack tipping over.
FIG. 2
UPRIGHT
BEAM
SECURING TAB
MOUNTING
PLATE
STUD
FIG. 4
LOOSEN/
TIGHTEN
SECURING
NUTS
TO ROTATE
OR ADJUST
HEIGHT OF
MOUNTING
PLATES
FIG. 6
GOOD:
STUD MUST
PROTRUDE
BY THREE
OR MORE
THREADS
Mounting Plate Securing (Fig. 7)
NOTE: When securing the mounting plates to the ground follow proper
procedures for using concrete wedge anchors. If you are uncertain about
the proper procedures, then please contact your local hardware store.
1. Using the supplied concrete wedge anchors, (3) of each will be
dedicated to (1) mounting plate. The orientation of the plates is up to
the user's discretion.
2. Follow proper procedure to install the concrete wedge anchors.
3. Check for levelness of the rack and make adjustment as necessary.
Then, tighten the securing nuts on all (4) mounting plates.
FIG. 7
CAUTION:
Do not stand on this product.
cause personal injury.
One Year Limited Warranty
D WALT will replace these mounting plates due to faulty materials or
E
workmanship for one year from the date of purchase (please be sure
to keep your receipt). This warranty does not cover part failure due to
normal wear or rack abuse. This warranty does not apply to accessories
or damage caused where repairs have been made or attempted.
For further detail of warranty coverage, call 1-844-377-8451.
In addition to the warranty, D
E
90 Day Money Back Guarantee
If you are not completely satisfied with the performance of your D
Pack Mounting Plate for any reason, you can return it within 90 days from
the date of purchase with a receipt for a full refund – no questions asked.
Latin America
This warranty does not apply to products sold in Latin America.
For products sold in Latin America, see country specific warranty
information contained in the packaging, call the local company or see
website for warranty information.
FIG. 5
BAD:
NEVER
ALLOW STUD
TO BE
RECESSED
IN TOP
SECURING
NUT
You may fall which may
WALT mounting plates are covered by our:
WALT 4
E