EINHELL TE-SM 2534 Dual Mode D'emploi D'origine page 27

0°-45° to the right in relation to the stop rail (dou-
ble miter cut).
•
If required, dismantle the clamping device
(8) or mount on the opposite side of the fixed
saw table.(18)
•
Move the machine head (4) to its upper po-
sition.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Use the handle (1) to adjust the turntable (17)
to the angle required (in this connection see
also section 6.2).
•
Retighten the locking screw (14) to secure the
turntable in place.
•
Adjust the miter angle on the machine head
and the stop rail as described under points
5.5 and 5.6.
•
Cut as described in section 6.1.
6.5 Limiting the cutting depth (Fig. 3)
•
The cutting depth can be infinitely adjusted
using the screw (27). To do so, undo the
knurled nut on the screw (27). Turn the screw
(27) in or out to set the required cutting depth
and then retighten the knurled nut on the
screw (27).
•
Check the setting by completing a test cut.
6.6 Sawdust bag (Fig. 3)
The saw is equipped with a sawdust bag (22) for
sawdust and chips. Slip the sawdust bag onto the
connector alongside the transport handle (34).
The sawdust bag (22) can be emptied by means
of a zipper at the bottom. The sawdust bag can be
removed in order to connect the suction hose of
a dust extractor (wet and dry vacuum cleaner or
extraction system). The extraction system is then
plugged onto the same position (suction hose/
extraction system is not included in the scope of
this delivery).
6.7 Changing the saw blade (Fig. 1, 19-21)
•
Warning! Before changing the saw blade:
Pull out the power plug!
•
Caution! Wear work gloves to prevent in-
jury when changing the saw blade.
•
Swing the machine head upwards (4).
•
Press the saw shaft lock (5) with one hand
while positioning the Hexagon key (45) on
the flange bolt (31) with the other hand. The
saw shaft lock (5) engages after no more
than one rotation.
•
Now, using a little more force, slacken the
flange screw (31) in the clockwise direction.
•
Turn the flange screw (31) right out and remo-
Anl_TE_SM_2534_Dual_SPK9.indb 27 Anl_TE_SM_2534_Dual_SPK9.indb 27
GB
ve the external flange (32).
•
Take the blade (7) off the inner flange and pull
out downwards.
•
Carefully clean the flange screw (31), outer
flange (32) and inner flange.
•
Fit and fasten the new saw blade (7) in rever-
se order.
•
Important! The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Important! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (12) in both perpendicular and
45° angle settings.
•
Important! The work to change and align the
saw blade (7) must be carried out correctly.
6.8 Transport (Fig. 1-3)
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Activate the release button (3), press the ma-
chine head (4) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
•
Fix the saw's drag function with the locking
screw for drag guide (24) in rear position.
•
Carry the equipment by the fixed saw table
(18) and the transport handle.
•
To set up the equipment again, proceed as
described in section 5.2.
6.9 Operating the laser (Fig. 3)
To switch on: Move the On/Off switch (36) to the
"I" position to switch on the laser (30). A laser line
is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
To switch off : Move the On/Off switch (36) to the
"0" position.
6.10 Operating the LED lamp (Fig. 3)
•
For good illumination of the work area you
can use the LED lamp in addition to the room
lighting.
•
On/Off switch for LED lamp (35)
•
To switch on: Switch position „I"
•
To switch off: Switch position „0"
•
If the machine is equipped with an LED, this
LED is not allowed to be replaced by a diffe-
rent type of LED. Repairs are allowed to be
carried out only by the manufacturer of the
- 27 -
24.10.2019 12:03:42 24.10.2019 12:03:42