User Interface - Honeywell HPA710 Série Instructions D'utilisation

ENGLISH (GB)
COMPONENTS
(See page 1)
1. Front Panel
2. Permanent Washable Mesh Pre-Filter
3. Granular Carbon Filter (
4. Certified True HEPA Filter (
5. Control Panel
a. Auto-Off Timer
b. Power – On/Off
c. Purification Level
d. Auto Mode
e. Ionizer – On/Off
f. SilentSleep™ Mode
g. Child Lock
h. Check Filter Light and Reset
6. Power Cord
7. AQSense™ Particle Sensor Door

USER INTERFACE

Symbol Function
ON / standby
Auto off timer
Purification level
Auto mode
Ionizer On/Off
SilentSleep™ mode
Child lock
Check filter light and reset
HOW YOUR AIR PURIFIER WORKS:
The Premium Honeywell air purifier uses a powerful 4
stage system to help purify the air that passes through the
filters in the unit.
Step 1 Air is drawn continuously in through the sides of the
unit by a powerful fan.
Step 2 Washable Permanent Mesh Filter captures larger
particles in the first stage, such as dust, and pet hair.
Step 3 Air passes through the Granular Carbon Filter in
the second stage, to remove odour, gases and VOCs
including formaldehyde.
Step 4 Air passes through the True HEPA Filter in the third
stage, to remove 99.97% of particulate matter as small
as 0.3 microns.
)
L
)
Step 5 Optional Ionizer, when selected, helps to boost the
cleaning performance. This is the final stage.
Step 6 Cleaner air is released from the top of the unit.
Step 7 The AQSense™ particle sensor, will continuously
monitor the quality of the air and the LED visually
displays the colour of light to indicate the quality of the
air in your room.
SET-UP
• Select a firm, level, and flat location. For best airflow,
locate the unit 6 inches from any wall or furniture.
• When operating, large volumes of air are drawn toward
the air purifier. Surrounding areas should be cleaned and/
or vacuumed frequently to prevent build-up of dust and
other contaminants. This may also help prolong the life of
the filter. If the unit is placed on a light coloured carpet,
a small mat or rug should be used underneath to prevent
staining. This is especially important in homes with
contamination from smoking or fireplaces.
FIRST TIME USE
The Certified True HEPA Filter,
Filter, and Mesh Pre-filter are supplied within the air
purifier. New air purifiers have their filters wrapped to
ensure purity, and are labeled to help identify the proper
replacement filter.
Before using your new air purifier you must remove the
plastic wrapper covering the
Granular Carbon Filter.
L
Make sure the air purifier is OFF and unplugged. Pull the
front panel toward you to remove it (see Fig. 1). Remove
the Mesh Pre-filter using the two pull tabs near the center
(see Fig. 2). Remove the Granular Carbon Filter (see Fig. 3).
Remove the True HEPA Filter (see Fig. 4). Remove plastic
from the filters.
Reinsert the True HEPA Filter into the air purifier
housing with the arrows pointing toward the unit (see Fig.
5). Reinsert the Granular Carbon Filter into the air
L
purifier housing (see Fig. 6). Reinsert the Mesh Pre-filter
into the air purifier housing with the two pull tabs facing
out. Ensure the top, bottom and side tabs are inserted in
the slots in the air purifier housing to fit securely (see Fig.
7). Replace the front housing panel by lining up the tabs
at the bottom of the panel with the slots in the air purifier
housing. Push the top of the panel towards the unit until it
snaps in place (see Fig. 8).
OPERATING INSTRUCTIONS:
• Ensure the air purifier is plugged into a working electrical
outlet, an audible 'beep' and the power light will illuminate
when plugged.
• Press the power button ( ) once. The unit will start at
the "general cleaning" level and remain on this setting
until another cleaning level is chosen.
2
(See page 1)
Granular Carbon
L
True HEPA Filter and