Additional Instructions For Work With The Battery Pack; Fitting And Removing The Battery Pack; Battery Charging - SPARKY HD Professional BR2 10.8Li HD Notice Originale

Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminium foil, or any build-
up of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cav-
ity. Unplug charger before attempting to clean.
▪ Do not freeze or immerse charger in water or any
other liquid.
VI - Additional instructions
for work with the
battery pack
▪ The battery pack for this tool has been shipped in a
low charge condition. You should charge the battery
pack fully before use.
WARNING: If the battery pack is cracked or
damaged in any other way, do not insert it in the char-
ger. There is a danger of electric shock.
▪ To ensure the longest battery life and best battery
performance, always charge the battery when the air
temperature is between 18–24°C. Do not charge the
battery pack when the temperature is below 0°C, or
above 40°C. This is important. Failure to observe this
safety rule could cause serious damage to the bat-
tery pack.
▪ The charger and battery pack may become warm to
touch while charging. This is a normal condition, and
does not indicate a problem.
▪ To prevent overheating, do not charge battery packs
in direct sunlight in hot weather or near heat sources.
▪ Do not charge inside a box or container of any kind.
The battery must be placed in a well ventilated area
during charging.
▪ When the battery is defective, liquid can escape and
come into contact with adjacent components. Check
any parts concerned. Clean such parts or replace
them, if required.
▪ If the battery pack does not charge properly:
(1) Check current at receptacle by plugging in a lamp
or other appliance.
(2) Move charger and battery pack to a location where
the surrounding air temperature is approximately 65°F–
75°F (18°C–24°C).
(3) If charging problems persist, take or send the tool,
battery pack and charger to your local service centre.
▪ The battery pack should be recharged when it fails to
produce sufficient power on jobs, which were easily
done previously. DO NOT CONTINUE to use under
these conditions. Follow the charging procedure. The
Li- ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging proce-
dure does not damage the battery.
▪ Do not incinerate the battery pack even if it is seriously
damaged or can no longer hold a charge. The battery
pack can explode in a fire.
▪ To facilitate the cooling of the battery pack after use,
avoid placing the charger or battery pack in a warm
6
EN
pages BR2-10.8LiHD-2012.indd 6
environment such as in a metal shed, or an uninsu-
lated trailer.
WARNING: Never attempt to open the battery
pack for any reason. If the plastic housing of the bat-
tery pack breaks or cracks, return to a service centre
for recycling.
READ ALL OF THE INSTRUCTIONS IN THE CHARG-
ER SECTION OF THIS MANUAL BEFORE ATTEMPT-
ING TO CHARGE THE BATTERY PACK FOR YOUR
TOOL.
▪ Always use correct SPARKY battery pack (the one
supplied with tool or a replacement pack exactly like
it). Never install any other battery pack. It will ruin your
tool and may create a hazardous condition.
▪ Charge battery packs only in SPARKY chargers.
▪ Use an environmentally safe disposal unit at a munici-
pal waste disposal centre to dispose of a damaged or
worn out battery.

FITTING AND REMOVING THE BATTERY PACK

To remove the battery from the machine: press the bat-
tery release buttons (4) and take the battery out of the
tool.
WARNING: Always set the forward/reverse
switch (3) in central position before any work on the
machine e. g. fitting and removing a battery, changing
the bit,, transport, maintenance and storage.
To install the battery: Insert the charged battery into the
opening at the base of the power tool until the battery is
securely latched with a click.

BATTERY CHARGING

▪ Insert the plug of the charger in the socket. The green
LED on the charging indicator (11) will start to glow
thus indicating that the charger is in standby state.
▪ Insert the battery (5) in the charger socket (10) consid-
ering the polarity. (Fig. 1)
▪ A new battery will work properly after five cycles of
charging and discharging. Charge and discharge a
battery, which is not used for a long time, for two to
three times to function well.
▪ When the battery working time is remarkably short de-
spite full charging, the life of the battery may be over.
Replace the battery immediately.
WARNING: The battery will be fully charged
after approximately 30 min, remove it from the charger
after this time.
Charging indication:
▪ The green LED starts to glow upon plugging the
charger in the mains.
▪ The green LED ceases to glow and the red LED lights
up after the battery has been placed in the charger,
thus indicating the beginning of the charging process.
BR2 10.8Li HD
26.9.2012 . 13:25:31 .