BEGLEC JB SYSTEMS MICRO LED MANAGER Mode D'emploi page 6

ENGLISH
 Set the DMX-channel, that you want to assign as DMX-start address on your Micro LED Manager
to maximum (value 255)
 Press the "Auto DMX address" button (6) on the Micro LED Manager shortly.
 If you want to set another unit to the same DMX-start address, simply press it's "Auto DMX
address" button (6) and it will receive the same address.
 Done!
An example to make things clear:
We will set the DMX start address of a Micro LED Manager to 106:
 Connect the Micro LED Manager to the DMX-controller as described above and make sure all is
switched on.
 Set all DMX-channels on the controller to zero (000)
 Now set DMX-channel 106 to maximum (255)
 Press the "Auto DMX address" button (6) on the Micro LED Manager shortly.
 Done!  Your Micro LED Manager now has DMX address 106!
B. Automatic DMX-addressing, starting from any given start address:
To save a lot of time (imagine the time it takes to set the DIP switches of 16 units...) you can set the
DMX addresses of all units in the DMX-chain just by the push of a button. No need to calculate the
starting address of each individual unit, this will be done for you!
 Make sure that ALL DIP-switches are set to OFF position!
 Make sure the DMX cables of all units are connected.
 Connect the first unit to a universal DMX controller.
 Connect all units to the mains so they are switched on.
 Set all DMX-channels on your DMX-controller to zero (value 000).
 Set the DMX-channel, that you want to assign as DMX-start address on your Micro LED Manager,
to maximum (value 255)
 Press the "Auto DMX address" button (6) on the first Micro LED Manager in the chain for about
5seconds.
 Done!  The first Micro LED Manager in the chain will receive the DMX-start address you chose
and it will automatically calculate and program the DMX addresses of all the other units in the
DMX-chain!
An example to make things clear:
We want to set the DMX-addresses of 16 units, the DMX start address of the first Micro LED
Manager must be 202:
 Connect all Micro LED Manager to the DMX-controller as described above and make sure all are
switched on.
 Set all DMX-channels on the controller to zero (000)
 Now set DMX-channel 202 to maximum (255)
 Press the "Auto DMX address" button (6) on the first Micro LED Manager in the chain for about
5seconds.
 Done!  The first Micro LED Manager in the chain will receive DMX-start address 202 and it will
automatically calculate and program the DMX addresses of all the other units in the DMX-chain!
nd
This means that the 2 Micro LED Manager automatically receives address 206, the 3
th
address 210, ..., until the 16 Micro LED Manager who automatically receives start address 262.
You just programmed 16 Micro LED Managers, this took you about 10seconds!!!
Remark: you can mix the units with other DMX-effects that don't have the automatic DMX-
addressing option. In that case you still have to set the DMX-addresses of these DMX-effects
manually! You can also mix the Micro LED Managers with other JB Systems LED products that have
the auto DMX-feature. They will also automatically receive their DMX-addresses.
C. Setting DMX-addresses using the DIP switches:
This is the traditional addressing method, this method should be used when used with the LED
WALL DIMMER. The first 9 DIP-switches correspond to a certain DMX-value:
DIP #1 #2 #3
Value 1 2 4
You can combine the values of these switches to obtain any starting address between 1 and 512:
Begin address = 01  switch 1=ON
Begin address = 05  switch 1+3=ON
JB SYSTEMS®
OPERATION MANUAL
#4 #5 #6 #7 #8 #9
8 16 32 64 128 256
values: 1
values: 1+4 = 5
7/54 MICRO LED MANAGER
ENGLISH
Begin address = 09
Begin address = 13
...
Begin address = 62
OPERATING INSTRUCTIONS
A. Standalone 1unit:
 Connect the LED projectors to the Micro Led Manager as indicated in the previous chapters.
 Switch the unit on and refer to the chapter "DIP SWITCH SETTINGS" to make yourself familiar with
the various functions of the faders and buttons.
B. Two or more units in master/slave setup:
 Connect the LED projectors to the Micro Led Managers as indicated in the previous chapters.
 Connect the units with each other as explained in the chapter about electrical installations.
 Switch the Micro Led Managers on. You can only use the controls on the master unit, the controls on
the slaves are disabled. Refer to the chapter "DIP SWITCH SETTINGS" to make yourself familiar with
the various functions of the faders and buttons on the master unit.
C. Connect the optional LEDCON-02 (or LEDCON-01) for remote control:
In most cases the MICRO LED MANAGER will be installed on a wall, close to the LED-projectors. If you
want to have easy access to its functions, you can connect the LEDCON-02 (or LEDCON-01) remote
controller to the (first) Micro Led Manager. The other connections are identical to those of the standalone
or master/slave setups. Don't forget to perform the automatic addressing on the LEDCON-02!!!
D. Controlled by universal DMX-controller:
 Connect the LED projectors to the Micro Led Manager(s) as indicated in the previous chapters.
 Connect the Micro Led Manager(s) with all other DMX-appliances in the DMX-chain.
 Switch all units on and set the proper DMX-addresses. (don't forget to set DIP-switch 10 to OFF)
 Switch your universal DMX-controller on and refer to the DMX chart below to control the connected
Micro Led Managers:
rd
has
JB SYSTEMS®
OPERATION MANUAL
 switch 1+4=ON values: 1+8 = 9
 switch 1+3+4=ON values: 1+4+8 = 13
 switch 2+3+4+5+6=ON values: 2+4+8+16+32 = 62
8/54 MICRO LED MANAGER