How To Use The Advanced Functions; Self Clean Function - CIAT RG57A3/BGEF Manuel D'utilisation

How To Use The Advanced Functions

TURBO function
The TURBO function makes the unit work
extra hard to reach your present temperature
in the shortest amount of time possible.
When you press the TURBO button in
COOL mode, the unit will blow cool air
with strongest wind setting to jump-start
the cooling process.
When you press the TURBO button in
HEAT mode, for units with Electric heat
elements, the Electric Heater will activate
and jump-start the heating process.

SELF CLEAN function

Airborne bacteria can grow in the moisture
condenses around heat exchanger in the unit.
With regular use, most of this moisture is
evaporated from the unit. By pressing the
CLEAN button, your unit will clean itself
automatically. After cleaning, the unit will turn
off automatically. Pressing the CLEAN button
mid-cycle will cancel the operation and turn
off the unit.
You can use CLEAN as often as you like.
Note: You can only activate this function
in COOL or DRY mode.
FOLLOW ME function
The FOLLOW ME function enables the
remote control to measure the temper-
ature at its current location. When using
AUTO, COOL, or HEAT functions,
measuring ambient temperature from
the remote control (instead of from the
indoor unit itself) will enable the air
conditioner to optimize the temperature
around you and ensure maximum comfort.
1. Press FOLLOW ME button to activate
function. The remote control will send
temperature signal to the indoor unit
every three minutes.
2. Press FOLLOW ME button again to
turn off this function.
ECO function
(RG57A8(B)/BGEF model only)
Used to enter the energy efficient mode.
Under cooling mode, press this button,
the remote controller will adjust the
temperature automatically to 24 C, fan
speed of Auto to save energy(but only
if the set temperature is less than 24 C).
If the set temperature is above 24 C ,
press the ECO button, the fan speed
will change to Auto, the set temperature
will remain unchanged.
NOTE:
Pressing the ECO button, or modifying
the mode or adjusting the set temperature
O
to less than 24 C will stop ECO operation.
Under ECO operation, the set temper-
that
O
ature should be 24 C or more. it may
result in insufficient cooling. If you feel
uncomfortable, just press the ECO
button again to stop it.
ON/OFF
ECO
TIMER
MODE
ON
TEMP
TIMER
FAN
OFF
SLEEP FRESH
TURBO CLEAN LED FOLLOW
MODEL:RG57A8(B)/BGEF
13
How To Use The Advanced Functions
O
O
O
ON/OFF
MODE
TEMP
FAN
SLEEP FRESH
TURBO CLEAN
MODEL:RG57A3(B)/BGEF
SHORTCUT function
(RG57A3(B)/BGEF model only)
Used to restore the current settings or resume
previous settings.
Push this button when remote controller is on, the
system will automatically revert back to the
previous settings including operating mode, setting
temperature, fan speed level and sleep feature
(if activated).
If pushing more than 2 seconds, the system will
SHORT automatically restore the current operation settings
CUT
including operating mode, setting temperature, fan
TIMER
speed level and sleep feature(if activated ).
ON
TIMER
OFF
SWING function
Swing Button
LED
FOLLOW
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press. If keep pushing more than 2
seconds, the vertical louver auto swing feature
is activated.
Swing Button
Used to stop or start horizontal louver movement
or set the desired up/down air flow direction. The
louver changes 6 degree in angle for each press.
If keep pushing more than 2 seconds, the louver
will swing up and down automatically.
SLEEP Function
The SLEEP function is used to decrease
energy use while you sleep (and don t need
the same temperature settings to stay
comfortable). This function can only be
activated via remote control.
Note: The SLEEP function is not available
in FAN or DRY mode.
,