Switching The Machine On And Off; Accessories; Maintenance And Cleaning; Technical Data - Germania GPT–CD006 Mode D'emploi

*
• Select a low setting for small screws or
soft work material.
• Select a high setting for large screws,
hard work materials and when remov-
ing screws.
• You should preferably choose a setting
as low as possible when driving screws.
Select a higher setting if the motor slips
before the screw is fully tightened.
WARNING: If the power tool gets exces-
sively hot in use, stop using the tool immedi-
ately and allow to cool before continuing
work. The cooling period can be reduced by
operating the drill at maximum speed with
no load. Always make sure the Motor Vents
(5) are not blocked and do not allow dust to
enter the body of the tool through the Motor
Vents; dust, especially metallic dust, may
damage or destroy the tool.

Switching the machine on and off

11.6
The on/off switch (12) is used for activating
the machine and adjusting rotation speed.
• Pressing the on/off switch (12) will
activate the machine, the further the
switch is being pushed, the faster the
drill will turn.
• Releasing the on/off switch (12) will
stop the machine.
LED lamp
11.7
The LED lamp (13) will be lit automatically
as soon as you press the ON/OFF switch
(12).

12. Accessories

Use only accessories with an allowable
speed matching at least the highest no-load
speed of the tool.
GERMANIA offers a wide range of suitable
accessories for an optimum performance
of your tool.
You can find the accessories in every Son-
derpreis Baumarkt or online: www.sonder-
preis-baumarkt.de.

13. Maintenance and Cleaning

WARNING: Always disconnect from the
mains power supply, before carrying out any
maintenance/ cleaning of the charger.
7063099-Cordless_Impact_Drill-18V-Ma-1903-19.indb 19
Remove the battery before carrying out any
maintenance/cleaning of the tool.
Maintenance
13.1
There are no inner parts of the tool which
need maintenance.
Cleaning
13.2
• Keep safety devices, ventilation open-
ings and the motor housing as free as
possible from dirt and dust. Rub the
electric power tool with a clean cloth or
blow over it with low pressure com-
pressed air.
• We recommend that you clean your
electric power tool immediately after
each use.
• Clean the electric power tool regularly
with a damp cloth and somewhat soft
soap.
Do not use any cleaning or solvent materi-
als; these can attack the device's plastic
components. Make sure that no water can
get inside the electric power tool.

14. Technical data

Speed . . . . . . . . . . 0 – 450 / 1650 min
Impacts per Minute 0 – 8100 / 29 700 min
Chuck . . . . . . . . . . . . . . . max. 13 mm
Max. Torque . . . . . . . . . . . . . . 40 Nm
Sound Pressure Level L
(In Wood) . . . . . . . . . . . . . . . 71 dB(A)
(In Concrete) . . . . . . . . . . . . . 82 dB(A)
Uncertainty K . . . . . . . . . . . . . . . 3 dB
pA
Sound Power Level L
WA
(In Wood) . . . . . . . . . . . . . . . 82 dB(A)
(In Concrete) . . . . . . . . . . . . . 93 dB(A)
Uncertainty K . . . . . . . . . . . . . . 3 dB
WA
Hand Arm Vibration
(No Load) . . . . . . . . . . . . . . . 1.32 m/s
(In Wood) . . . . . . . . . . . . . . . .3.0 m/s
(In Masonry) . . . . . . . . . . . . . 9.89 m/s
Uncertainty K. . . . . . . . . . . . . .1.5 m/s
English
-1
-1
pA
2
2
2
2
19
28/03/2019 11:05