Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
d)
Keep power tools which are not in use away
from children.
Only persons who are familiar with the power
tool and who have read the operating instruc-
tions may use the power tool. Power tools are
dangerous if used by inexperienced persons.
e)
Maintain power tools with care.
Check moving parts for proper function and
smooth running, and check whether there are
parts which are broken or damaged to the ex-
tent that the functionality of the power tool is
impaired. Have damaged parts repaired before
using the power tool. Many accidents are caused
by poorly-maintained power tools.
f)
Keep cutting tools sharp and clean. Carefully
maintained cutting tools with sharp edges
are less likely to jam and can be guided more
easily.
Use power tools, accessory parts, insertion
g)
tools, etc. in compliance with these instruc-
tions.
Take into account the working conditions and the
activity which is to be carried out. Using power
tools for applications other than those intended
may cause dangerous Situations.
Service
a)
Have your power tool repaired by qualified
specialists only, and always use original
spare parts for repair. This is to maintain the
safety of the power tool.
Safety notes for all applications- General safety
notes for grinding, sanding, working with wire
brushes, polishing and cutting by grinding
a)
This power tool must be used as a sandpaper
grinder.
Observe all safety notes, instructions, illustra-
tions and data which are provided together with
the tool. Nonobservance oft he following instruc-
tions may result in electric shock, fire and/or se-
vere injury.
b)
This power tool is not suited for grinding,
Operations with wire brushes, polishing and
cutting by grinding.
Using the power tool for applications other than
the intended ones may result in risks and injury.
c)
Only use accessory parts especially pro-
vided for this tool and recommended by the
manufacturer.
The mere fact that you can mount accessory
parts to your power tool does not ensure safe
use.
d)
The permissible speed of the insertion tool
must be at least as high as the maximum
speed specified on the power tool.
Accessories with a higher speed may break and
fly off.
18 І 36
e)
The outer diameter and the thickness of the
insertion tool must comply with the dimen-
sions specified on your power tool.
lt is not possible to shield or control insertion
tools with different dimensions.
Grinding disks, flanges, grinding plates or
f)
other accessory parts must exactly mate the
grinding spindie of your power tool.
nsertion tools which do not exactly mate the
grinding spindle of your powertool will perform ir-
regular rotations, cause high vibrations and thus
the loss of control.
Do not use damaged insertion tools.
g)
Prior to each application, you must check inser-
tion tools such as grinding disks for chippings and
cracks, grinding plates for cracks, wear or major
abrasion, wire brushes for loose or broken wires. lf
the power tool or insertion tool falls down, you must
check it for damages, or use an undamaged inser-
tion tool. After you have checked and inserted the
insertion tool, both you and persons in the vicinity
must stay out of the Ievel of the rotating insertion
tool, and the tool must be operated at maximum
speed for one minute. Most of the damaged inser-
tion tools will break within this test period.
Wear personal protective equipment.
h)
Depending on the application of the power tool,
you must wear a full face shield, eye protection
or goggles. lf appropriate, you must wear a dust
mask, hearing protection, protective gloves or a
special apron which protects you against small
grinding chips and material particles. Protect your
eyes against foreign objects which fly off du ring
different operations. The purpose of dust masks
and breathing equipment is to filter the dust gener-
ated during the operation. Long-term exposure to
high noise pollution may cause hearing loss.
i)
Make sure that other persons stay a safe dis-
tance away from your working area.
Persons accessing your working area must wear
personal protective equipment. Fragments of the
work piece or broken insertion tools may fly off
and cause injury even outside the direct working
area.
j)
Always hold the tool by its insulated han-
dles when the insertion tool may come into
contact with hidden power lines or with the
power cord of the power tool.
Contact with live lines may energise metal tool
parts and cause electric shock.
k)
Keep the power cord away from rotating in-
sertion tools.
lf you lose control of the power tool, the power
cord may be cut or trapped, and your hand or
arm may get into the path of the rotating inser-
tion tool.
l)
Never put aside the power tool before the
complete halt of the insertion tool.
Rotating insertion tools may get in contact with
the place of deposit thus causing the loss of con-
trol of the tool.
Publicité
Table des Matières
