Installation/Connection; Basic Procedure - Kenwood KDC-X301 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

REFERENCES
Source name
2
STANDBY
Source name
(*
)
2
TUNER
Frequency
(*
)
Clock
(For FM Radio Broadcast Data System stations/FM Radio Data
System stations only)
2
Station name
(*
)
Clock
(back to the beginning)
CD or USB
(For CD-DA)
2
Disc name/Artist
(*
(back to the beginning)
(For MP3/WMA/AAC/WAV/FLAC files)
2
Track title/Artist
(*
)
Playing time
Clock
iPod USB/
When [MODE OFF]/[BROWSE MODE] is selected ( 9):
2
iPod BT or
Track title/Artist
(*
)
ANDROID
(back to the beginning)
2
PANDORA/
Station name
(*
)
PANDORA BT
Album title
Playing time
2
IHEARTRADIO
Station name
(*
)
2
BT AUDIO
Track title/Artist
(*
)
(back to the beginning)
2
AUX
Source name
(*
)
*
1
Battery and signal strength of the Bluetooth device will be shown if [BATT/SIGNAL] is set
to [AUTO]. ( 17)
*
2
Only for
: Turn off the display information.
Display information
/
Clock
(back to the beginning)
(back to the beginning)
Radio text
Radio text+
Title/Artist
)
Track title/Artist
Playing time
Clock
Album title/artist
Folder name
File name
(back to the beginning)
Album title/Artist
Playing time
Clock
Shared/Radio station
Track title
Artist
Clock
(back to the beginning)
Track title/Artist
Clock
(back to the beginning)
Album title/Artist
Playing time
Clock
Clock
(back to the beginning)

INSTALLATION/CONNECTION

Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery's negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car's chassis again after installation.
Caution
Frequency
• For safety's sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the [ wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle's fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
• If the fuse blows, first make sure the wires are not touching car's chassis, then replace the old
fuse with one that has the same rating.

Basic procedure

1 Remove the key from the ignition switch, then disconnect the [ terminal of the car
battery.
2 Connect the wires properly.
See Wiring connection. ( 33, 34)
3 Install the unit to your car.
See Installing the unit (in-dash mounting). ( 32)
4 Connect the [ terminal of the car battery.
5 Press
to turn on the power.
6 Detach the faceplate and reset the unit. ( 3)
31
ENGLISH

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Kdc-bt21Kdc-mp368btKmr-d368bt

Table des Matières