Assembly And Installation - Dupla MARIN Multireaktor MR 750 Mode D'emploi

Fluidized Bed Reactor / Pellet Reactor
Thank you for choosing to purchase the Multireaktor. The Multireaktor is multifunctional. It can be installed standing in the filter's core pool
or as a Hang-On-System directly at the aquarium. The Multireaktor is suitable both for fresh and marine water aquaria.
Possible applications: The Multireaktor comes with two differently perforated plates which should be arranged according to the reactor's
operating purpose as follows. For the use with biopellets (such as DuplaMarin Biopellets NP), it is recommended to use the perforated plate with
diameter 3 mm holes as the bottom plate to achieve a better swirling motion of the material. When using more finely granulated adsorbers (such
as DuplaMarin Siliphos as a phosphate and silicate adsorber) or filtering coal (such as DuplaMarin Carbon premium), the plate with the diameter
2 mm holes should be used as the bottom plate.

Assembly and installation:

The Multireaktor is all-purpose:
· as a standing filter next to or in the filter's core pool
· as a filter underneath the aquarium
· as a Hang-On-System mounted directly to the aquarium
The installation of the Multireaktor is carried out with a separate pump or filter by means of tube connectors which are marked IN and OUT.
To open the Multireaktor, release the 5 screws at the lid of the Multireaktor. Subsequently, the lid can be removed from the housing, the
perforated plates of the Multireaktor should be mounted in accordance with the intended use. When you start the filling, put the standing pipe
with the mounted perforated plate into the filter first. The second perforated plate is mounted after the filling. When using very fine materials, a
filter sponge should be inserted underneath the perforated rod (on top of the material). When mounting the lid, pay attention to the correct fit of
the o-ring seal.
Mounting with using DuplaMarin Siliphos:
Perforated plate with diameter 2 mm holes as bottom plate
Multireaktor 750, Filtering flow rate: 300 l/h max.
Filling capacity: 500 ml
Size of aquarium: depends on the load, up to 2,000 l of marine
water/4,000 l of fresh water (at 0.5 mg / PO
Multireaktor 1.500, Filtering flow rate: 600 l/h max.
Filling capacity: 1,000 ml
Size of aquarium: depends on the load, up to 4,000 l of marine
water/8,000 l of fresh water (at 0.5 mg / PO
Multireaktor 4.000, Filtering flow rate: 1,000 l / h max.
Filling capacity: 2,000 ml
Size of aquarium: depends on the load, up to 6,000 l of marine
water/12,000 l of fresh water (at 0.5 mg / PO
Scope of delivery:
· Multireaktor
· 1x perforated plate 3 mm holes
· 1x perforated plate 2 mm holes
· 2x silicone tube
· Hang-On-System
· using instructions
4
/ l)
4
/ l)
4
/ l)
4
Mounting when using DuplaMarin Biopellets NP:
Perforated plate with diameter 3 mm holes as bottom plate
Multireaktor 750, Filtering flow rate: 400 –600 l/h
Filling capacity: 500 ml max.
Size of aquarium: depends on the load, up to 300 l
Multireaktor 1.500, Filtering flow rate: 600 – 1.000 l/h
Filling capacity: 800 ml max.
Size of aquarium: depends on the load, up to 800 l
Multireaktor 4.000, Filtering flow rate: 1.500 – 2.000 l/h
Filling capacity: 2.000 ml max.
Size of aquarium: depends on the load, up to 2.000 l