Maintenance; General; Daily Cleaning; Removing The Glass Panels - Hatco FLAV-R-FRESH Manuel D'installation Et D'utilisation

MAINTENANCE

General

Hatco Flav-R-Fresh Humidified Impulse Display Cabinets are
®
designed for maximum durability and performance, with
minimum maintenance.
WARNING
ELECTRIC ShOCK hAzARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• Use only Genuine hatco Replacement Parts when
service is required. Failure to use Genuine hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in hatco equipment.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized hatco Service
Agent or contact the hatco Service Department at 800-558-
0607 or 414-671-6350; fax 800-690-2966; or International
fax 414-671-3976.

Daily Cleaning

To preserve the finish of the Display Cabinet, perform the
following cleaning procedure daily.
NOTICE
Use non-abrasive cleaners only. Abrasive cleaners could
scratch the finish of the unit, marring its appearance and
making it susceptible to soil accumulation.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove and wash all food pans.
3. Wipe down all interior and exterior metal surfaces with a
damp, non-abrasive cloth. Stubborn stains may be removed
with a good non-abrasive cleaner. Clean hard to reach
areas using a small brush and mild soap.
NOTE: Both the rotating display rack and the stationary rack
are removable for cleaning, if necessary. Refer to the
"Removing the Rotating Rack" procedure in this section
for removal.
4. Wipe dry the entire unit using a clean and dry, non-abrasive
cloth.
5. Clean the glass side panels and door panel(s) using
ordinary glass cleaner and a damp, soft cloth or paper
towel. The side panels are removable for detailed cleaning,
if necessary. Refer to the "Removing the Glass Panels"
procedure in this section for removal.

Removing the Glass Panels

1. Lift the glass panel out of the bottom channel of the cabinet.
2. Pull the lower edge away from the cabinet.
3. Carefully lower the glass until the top clears the cabinet.
Replacing the Glass Panel
1. Position the glass panel with the top edge under the top
cabinet lip, and raise the glass until it clears the bottom
channel of the cabinet.
2. move the bottom of the glass towards the cabinet until the
glass rests against the cabinet frame.
3. Carefully lower the glass until it rests in the bottom channel
of the cabinet.

Removing the Rotating Rack

(FDWD-1, FDWD-2, and FDWD-12-1 Models)
1. Open the front access door.
2. Pull down the spring-mounted coupling to compress.
3. Tip the rack until the rack shaft clears the motor shaft.
NOTE: Do not remove the bow cotter pin from the rack shaft.
Decompressed
Coupling
Bow
Cotter Pin
Rack
Shaft
Compressed
Bow
Cotter Pin
Rack
Shaft
Removing motorized Display Racks
Replacing the Rotating Rack
1. Insert the rack into the cabinet and place the rack bottom
point in the dimple located at the center of the cabinet floor.
2. Pull down the spring-mounted coupling to compress.
3. Tip the rack to line up the rack shaft with the motor shaft pin.
4. Decompress the spring-mounted coupling until the coupling
is locked in place with the motor shaft pin.
12
English
Motor Shaft
Locked Position
Motor Shaft
Coupling
Unlocked Position
Form No. FDWDm-0915