Additional Safety Rules - Makita LS1214 Manuel D'instruction

Masquer les pouces Voir aussi pour LS1214:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Using a power source with voltage less than the
nameplate rating is harmful to the motor.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An
Ampere Rating
More Than
0
6
10
12
000173

ADDITIONAL SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to slide compound saw safety rules. If you use this
tool unsafely or incorrectly, you can suffer serious
personal injury.
1.
Wear eye protection.
2.
Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
3.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
4.
Do not perform any operation freehand. The
workpiece must be secured firmly against the
turn base and guide fence with a vise during
all operations. Never use your hand to secure
the workpiece.
5.
Never reach around saw blade.
6.
Turn off tool and wait for saw blade to stop
before
moving
settings.
7.
Unplug
tool
servicing.
8.
To reduce the risk of injury, return carriage to
the full rear position after each crosscut
operation.
9.
Always secure all moving portions before
carrying the tool.
10. Stopper pin which locks the cutter head down
is for carrying and storage purposes only and
Table 1: Minimum gage for cord
Not More Than
6
10
12
16
workpiece
or
before
changing
blade
undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. Table 1
shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the gage number,
the heavier the cord.
Volts
120 V
25 ft.
18
18
16
14
USB036-2
not for any cutting operations.
11.
Do not use the tool in the presence of
flammable liquids or gases.
12. Check the blade carefully for cracks or
damage before operation. Replace cracked or
damaged blade immediately. Gum and wood
pitch hardened on blades slows saw and
increases potential for kickback. Keep blade clean
by first removing it from tool, then cleaning it with
gum and pitch remover, hot water or kerosene.
Never use gasoline to clean blade.
13. While making a slide cut, KICKBACK can
occur. KICKBACK occurs when the blade
binds in the workpiece during a cutting
operation and the saw blade is driven back
rapidly towards the operator. Loss of control
and serious personal injury can result. If blade
begins to bind during a cutting operation, do
not continue to cut and release switch
immediately.
14. Use only flanges specified for this tool.
15. Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt.
Damage to these parts could result in blade
breakage.
changing
16. Make sure that the turn base is properly
secured so it will not move during operation.
or
Use the holes in the base to fasten the saw to a
stable work platform or bench. NEVER use tool
where
awkward.
17. For your safety, remove the chips, small
pieces,
operation.
18. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
4
Total length of cord in feet
50 ft.
100 ft.
AWG
16
16
16
14
16
14
12
Not Recommended
operator
positioning
etc.
from
the
150 ft.
14
12
12
would
be
table
top
before

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ls1214fLs1214lLs1214fl

Table des Matières