Milwaukee M18 FFN Notice Originale page 16

To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
"For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
OPERATION
There are two ways for working with this nailer (see also
picture section):
Single Sequential Actuation:
Drive the fastener by pulling the trigger.
Contact (Bump) Actuation:
Hold the trigger and drive the fastener by pushing the nailer
against the workpiece.
Reload Indicator
To indicate that the magazine is almost empty of fasteners
(about 4-5 left), the workpiece contact will not compress,
preventing operation under usual pressure. Install more
fasteners to continue working.
Setting the Depth of Drive (see picture section)
Know what is behind your workpiece. A fastener could travel
through the workpiece and out the other side, striking a
bystander and causing serious injury. Lower the depth of
drive to prevent the fastener from being pushed all the way
through the workpiece.
Thermal Overload
If the tool overheats, it will stop working and the power
button/actuation indicators will fl ash. Once the tool cools
down, the tool will revert to the selected mode. Restart work
as normal.
CLEARING A JAMMED FASTENER
Most jams are caused by a fastener or part of a fastener
wedging between the driver blade and the nail guide.
Fastener strips with an incorrect collation angle or the wrong
fastener gauge may cause continuous jamming.
To clear the jam:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
and others when installing or removing fasteners. Failure
to do so could result in injury.
30 ENGLISH
3. Remove fastener strip from magazine.
4. Remove the fastener using needle-nose pliers. If
necessary, remove magazine from tool.
5. Follow the steps under "Required Daily Testing" before
restarting the work.
REQUIRED DAILY TESTING
WARNING: To reduce the risk of injury to yourself
and others, test the tool before beginning work each
day or if the tool is dropped, received a sharp blow,
been run over, etc. Complete the following checklist IN
ORDER. If the tool does not work as it should, contact a
MILWAUKEE service facility immediately.
Always point tool away from yourself and others.
1. Remove battery pack.
WARNING! Always point the tool away from yourself
and others when installing fasteners. Failure to do so
could result in injury.
2. Check all screws, bolts, nuts, and pins on the tool. Any
loose fasteners must be tightened.
3. Pull back the fastener pusher on the magazine (to
override the Reload Indicator) and press the workpiece
contact against a workpiece. It must move smoothly.
4. With the workpiece contact pressed against the
workpiece, pull the trigger. It must move smoothly.
5. Insert battery pack.
6. Select the Single Sequential Actuation Operation.
Without pulling the trigger, pull back the fastener pusher
on the magazine (to override the Reload Indicator) and
press the workpiece contact against a workpiece. The
tool must not operate. Holding the workpiece contact
away from the workpiece, pull back the fastener pusher
on the magazine (to override the Reload Indicator). Pull
and hold the trigger for 5 seconds. The tool must not
operate. Continue to pull and hold the trigger and push
the workpiece contact against a workpiece. The tool
must not operate. Without pulling the trigger, pull back
the fastener pusher on the magazine (to override the
Reload Indicator) and press the workpiece contact
against a workpiece. Pull the trigger. The tool must
operate. Release the trigger. The driver must move up.
7. Select the Contact Actuation Operation. Holding the
workpiece contact away from the workpiece, pull back
the fastener pusher on the magazine (to override the
Reload Indicator) and pull the trigger. The tool must not
operate. Continue to pull and hold the trigger and push
the workpiece contact against a workpiece. The tool
must operate.
8. If all previous tests work properly, set the tool for your
work. Select the operation and load fastener strips.
9. Set the depth of drive according to the "Setting the
Depth of Drive" section and see picture section.
10. If all tests operate properly, the tool is ready for use.
Repeat these tests before use each day or if the tool is
dropped, received a sharp blow, been run over, jammed,
etc.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only Milwaukee accessories and Milwaukee spare
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Wear gloves!
Wear ear protectors!
Keep hands away!
Warning of gas cylinders
Do not dispose electric tools, batteries/
rechargeable batteries together with
household waste material.
Electric tools and batteries that have reached
the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
n No-load speed
0
V Volts
Direct current
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 31