Publicité
How to Mount Your Gate
3. To extend your Numi gate using the Index positions firstly you will need to unlock your gate. Your gate is
locked by four Indexed mechanism locks (ISS locks) indicated below.
4a. To unlock your ISS locks, take a small flat head screwdriver, insert to depress each button and push outwards
as indicated in the diagrams below. This process should be repeated on all four locks, two on either side
of your Numi gate.
Diagram 5
Schéma 5
Diagrama 5
4b. While holding the outer uprights of your Numi gate pull the gate outwards to extend. Each click you hear
represents an index position. Once you have extended your gate to the correct width, relock your Numi gate by
repressing each of the ISS button locks using your hands. You will hear a clicking sound when this has been done
properly. Please note that the buttons will not lock unless the gate is located in an index position.
Diagram 6
Schéma 6
Diagrama 6
5. Extensions : That is relevant to your opening width.
If required add a maximum of two extensions to a wall fixing plate as instructed in the diagram below. Simply slide
the Extensions down on the wall fixing plate until it clicks in place.
• Extensions must only be added to the wall fixing plate which holds the hinge of your Numi gate.
• If you do not use both of your supplied Extensions please keep them stored safely.
Diagram 7
Schéma 7
Diagrama 7
3
CCD-0012-021 REV1
(continued from page 2)
Diagram 4
Schéma 4
Diagrama 4
How to Mount Your Gate
6. WALL FIXING PLATE : Your Numi gate will need to be mounted to the wall
using the two wall fixing plates supplied to you. These will need to be drilled and
screwed to your wall.
WALL FIXING PLATE 1 : Measure 29" high from the floor at the point where you
would like to mount your gate. Make a mark. This is where you should drill the top
hole for your wall fixing plate. Using this wall fixing plate as a template you can mark
where the lower holes should be drilled into your wall. Ensure that the plate is at right
angles to the floor and attach using the most appropriate method below.
• We recommend you use a spirit level for accuracy.
• WARNING : DO NOT attach the hinge side fixing plate to a
dry walls. As not even modern homes have perfectly
parallel walls please refrain from attaching your second wall mount
to the wall just yet.
WOOD FIXING : Drill 2mm pilot holes and use the wood screws provided screw-
ing directly into the wood.
PLASTER WALL FIXING : Drill 5.5mm (7/32") holes and insert the wall plugs
provided before screwing into the wall.
DRY WALLS : Hollow walls constructed of dry wall require special fixing (not
supplied). You will need to purchase heavy duty expandable wall plugs (available at
DIY stores).
7. Sliding Your Numi Gate Onto Your Wall Fixing Plate : Now the initial
wall fixing plate is attached to your wall, slide your Numi gate on to it until it is fully
secure and you hear a clicking sound.
8. WALL FIXING PLATE 2 : Take your second wall fixing plate and slide on to your latch bracket as illustrated
(Diagram A). Line this up so that the top of your Numi gate is level with the top of the latch bracket. Make a mark at the top as
to where you need to attach the wall fixing plate to the wall (Diagram B).
• Please note that your latch bracket will be adjusted at a later stage so that your Numi gate will fit perfectly.
Remove the latch bracket from the wall fixing plate. While pushing the thumb release at the bottom
of the wall fixing plate lift the latch bracket to remove (Diagram C).
Align your wall fixing plate to the mark you have just made and attach it to the wall using the process explained.
Reattach the latch bracket to the second wall fixing plate (Diagram A).
Diagram A
Diagram B
Schéma A
Schéma B
Diagrama A
Diagrama B
9. INTEGRATED TUNING SYSTEM (ITS) : Now check if your Numi gate reaches the latch bracket. If it does not,
adjust the latch bracket using the Integrated Tuning System.
This is a simple trial and error process.
Using a screwdriver. wind the bracket
in/out at the ITS points shown below.
Once fitted correctly the gap between
the gate and the latch bracket should
be no more than 1mm.
• Please note that this process will
help you if your walls are uneven.
(continued from page 3)
29"
Diagram C
Schéma C
Diagrama C
wind out anti-clockwise
Dévissez dans le sens anti-horaire
gire hacia la izquierda
wind in clockwise
Vissez dans le sens horaire
gire hacia la derecha
CCD-0012-021 REV1
4
Publicité
